Question about Washing Machines

1 Answer

Fisher & Paykel Smart Drive 9- is POKED!!!

The machine starts the fill cycle, then stops, then it starts again, when its in a good mood it will do this a couple of times (to lead me on) and then it will beep furiously - please help:-)

Posted by on

  • Anonymous Jan 11, 2008

    Machine operates in spasms, then beeps till switched off!

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Hp laserjetm1005 mfp does not get print

Posted on Sep 16, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Direct drive whirlpool washer has electrical odor and stops.


the burn odour and stoppage an electrical fault and coupled with a 20 amp circuit breaker tripping indicates a motor fault
Capacitors are tested with an capacitance tester and not an ohm meter as ohms is a resistance and not capacitance reading
When breakers activate it indicates a massive short or current draw and the problem could be in the windings of the motor
could be water getting into the motor at times causing the intermittent problem
I would suggest that you call in a service technician or an accredited electrician to check out the machine properly

Jan 20, 2016 | Whirlpool Washing Machines

1 Answer

Fridgidaire FDB4050lhb1 restarts, stops, cycle problems


see the w. diagram, test for switch door
2) if the switch is defective, the starting relais will be over and over.
God bless you

5_10_2012_10_36_39_am.gif5_10_2012_10_37_00_am.gif

May 09, 2012 | Frigidaire 24 in. FDB635RF Built-in...

1 Answer

I started my machine and it started to fill and then I stopped to add a couple more things and I can't get it to restart. help


switch the power off for 1 min. then plug power back in and select spin cycle.(to get rid of the water. When all water is gone and drum starts to spin, switch off again. Select the normal wash you use all the time and see if all is ok.

Sep 30, 2010 | Maytag Neptune MAH6500A Front Load Washer

3 Answers

Starts and stops


A failed inlet valve is not uncommon in F&P machines. The hot valve is different to the cold one, so don't exchange them. Not a big job for a tech to do in-laundry. Good luck....Nomess

Jun 11, 2010 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Rental...no manuel...first time using washer. pushed regular, large, cold, pause resume. When it finished filling with water it beeps 3x than stops for a couple minutes then beeps 3x etc. It is filled...


Your problem is with the pause/resume button. This button allows you to add/remove items before the cycle is complete. If you press this button and there is water in the machine it will beep for a period of time (3 mins) and then empty the machine automatically so you can open the door. After opening the door the cycle can be restarted again by pressing the pause/resume button again.

Nov 07, 2009 | Washing Machines

1 Answer

Agitator starts at begining of cycle before washer is full


Please be carful as running the agitator without enough water will overheat and kick out the motor, however it should be ok when it resets itself.
Yes, the machine should stop agitating when you lift the lid so this too is part of the problem.
After looking at the print I can only suggest that the cam contacts in the timer ( contacts 12 and 14) that start the motor are burned and stuck together.
Quentin

Sep 17, 2009 | Frigidaire FEX831CS Top Load Stacked...

3 Answers

Maytag Atlantis stopped mid cycle


Bad/worn/broken lid switch look at the back of the lid there is a little lid cam there that hits a switch,if this switch isn't engaging it will do just what you are describing.use a small screw driver to push the button in and see if it starts.

Sep 03, 2009 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Neptune MAH3000AWW will start to fill when start is pressed, but stops seconds later


either a faulty pressure switch / pot or faulty controller - either way you will need to call someone in.

Jul 24, 2007 | Maytag Neptune Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...