Question about Washing Machines

1 Answer

Lg fuzzy logic 6.0kg lwd-6517s

After the machine is full of water,it starts washing for 5 seconds.then it stops and. makes an alarm showing d E on screen.

Posted by Anonymous on

Ad

1 Answer

Baboo Jankee

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Fuzzy logic 6,okg 6517s not spinning

Posted on Aug 23, 2019

Ad

5 Related Answers

Dissolu

Gintautas Maldzius

  • 221 Answers

SOURCE: I have an LG Fuzzy Logic top loader. it keeps draining water out

If it's really as you described, when draining at the same time filling up, then it's a problem in the main control board. You'll need some electronics knowledge to repair it, or just replace the main board

Posted on Aug 07, 2009

Ad

Anonymous

  • 4 Answers

SOURCE: I'm using LG Fuzzy logic 6.5kg WF-S6607TC.

Check the lid cover. At the edge, there is a plastic housing some sort of a magnet. This is the magnetic sensor for lid cover open protection.
If the magnet is not there, place a magnet at the position on the washer where the housing will come in contact with the washer when lid is close.

Posted on Sep 09, 2009

Anonymous

  • 1 Answer

SOURCE: LG Top load fuzzy logic washing machine DE problem.

I have the same problem. please let me know if yours got fixed

Posted on Dec 19, 2009

heatman101

D. Floyd Kolb

  • 43501 Answers

SOURCE: LG Top Loader Fuzzy Logic 5.5. The water

Hi,
No you just need to get the drain hose up higher...the water is siphoning out and is either caused by the end of the drain hose still in water and not having an air gap or the hose is not going up higher then the top of your washer...
Lifting the hose up should give you an air gap and get the hose high enough to stop the siphoning...

heatman101

Posted on Apr 28, 2010

Testimonial: "I am extremely impressed that this won't cost a call out service fee. . . and looking like a bimbo. thanks, heatman!"

m_yuzairi

  • 1 Answer

SOURCE: LG Fuzzy Logic 6.5 Kg WF-F733PC washing machine not spinning

hi...I have an LG Fuzzy Logic 6.5 Kg WF-F733PC washing machine & it's stop when 3-4 second start washing, wash and spin led appear also the buzzer bip contibuosly...any ideas?it's software problem....need advice

Posted on May 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stop running and start blinking and setting off alarm


looks like water pump is stook with a coin or faulty

Dec 31, 2017 | Washing Machines

1 Answer

Hi my Electrolux EWF1074 isn't working. The timer is counting down but there is no water in the machine. I tried resetting it but it didn't work. Could someone please help me. Regards Matt.


Rapid reading of alarms:

Press the START/PAUSE button and the nearest option button (4) simultaneously for at least 2 seconds: the LEDs initially switch off, and then display the flashing sequence indicating the last alarm.

ewf1074-2rgnvy5j4oifscmshudmmeh4-3-0.jpg After reading error code (look display) will be a lot clearer in which phase of the washing cycle has occurred or is happening malfunction.

New washing machine (electronic) compared to the old models (electromechanical) consume much less water, so it looks that your washing machine is working properly, otherwise it would be stopped. This will be confirmed if the display show E00 which means there is no any malfunction. Any other error code, for exp. E10,E20,E30, E40, E50...... means some malfunction.

Dado

Mar 11, 2017 | Electrolux Washing Machines

1 Answer

My zanussi zwg 6141p washing machine is calling water at start of cycle but is not going into drawer to swill out detergent , is also stopping half way with the green light on the start button flashin


Some appliances malfunction can be displayed in hexadecimal or in binary code.
So your device is defective and shows you what's wrong. You have to count how many times flashes red light and how many times flashes green light. Red light shows the first error number and green light the second error number.
For example: you forgot to close the door and you started washing machine. After some time (timeout) will generate an alarm. Four times will flash red light and once the green light which means error code " E41 " or "Open door"
" E20 " means "No drain water"
" E10 " means "No fill up water"


Dado

Sep 08, 2014 | Zanussi Washing Machines

1 Answer

Electrolux ESI 6180


I was shown how to clear your dishwasher and keep it running much longer. however, be careful when doing this. start with an empty dishwasher. pour 12 cups of cold water to the bottom area of tub and wearing latex, or rubber gloves, measre and por in exackly 2 cups of ammonia. let that solution sit there either all day, or overnight, at least a few hours, then run it through your machine, do not add anything else. do not do this with small children around. if you prefer buy the largest jug od vinegar (white) and pour it full strength into tub of your macine. let stand sevral hours, then put through a light or regulsr cycle. if you encountet that same problem empty, press drain cycle. retry usingrinse cycle instead. let me know if his resolnves your problem.

Nov 15, 2013 | Electrolux Dishwashers

1 Answer

We have a Duet Washing machine. It keeps sounding the alarm and then the letter F will show up followed by the letter H..do you have any idea what these warnings mean...it just stops working and keeps...


Hi

Error code FH appears when No water is detected entering machine or Pressure switch trip is not detected. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.
Press PAUSE/CANCEL twice to clear the display. If there is no water entering the unit then make sure that the inlet valves are working fine. You may need to check the continuity at the inlet valves. If the valves are fine then check whether inlet water hose, it may be plugged. Also check for inlet water screen at the valve. However, if the water is entering into the washer then the Drain pump might not be working. Also inspect the Pressure Switch hose whether it is in good condition and properly connected to Tub and Pressure switch. Also check hoses for leak and inspect the flow meter. Hope this helps...

Daniel

Feb 11, 2011 | Washing Machines

2 Answers

LG WF T6517TC Washing Machine does not fill water


sir
my washing machine WF-T6517TC
when it start to wash get Alarm "dE" beep and stop machine.
what need to do.
call me 91080843

Apr 10, 2010 | LG Washing Machines

2 Answers

WASHING MACHINE FILLS WITH WATER AT START THEN STOPS SHOWING ERROR 5


the usual issues with this type of washer is the relay board located inside the top of the unit. as i remember mfgs make a nice unit but are not so good for sealing the electronics off from the rest of the unit. chances are some moisture is up in the relay or relay socket. easy access you will see several relays. pull and tag each as you do to avoid confusion. check for corrision build up on any part of this unit. this should help.. gl k

Jun 10, 2007 | Hoover AAA140 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18397 Answers

Cindy Wells

Level 3 Expert

6133 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...