Question about Sharp AR-5316 Advanced Digital Imager Copier

4 Answers

Sharp ar-5316 i am getting code h4 when i start my copier. what is the problem.

Posted by on

  • Abdalla Bakhiet
    Abdalla Bakhiet May 03, 2008

    I turned the power supply ON & OFF

    I have cheked the fuser unit OK !

  • Anonymous Feb 02, 2009

    the problem code H4 is occured when machine is switch ON

×

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I am getting a problem code H4 for sharp copier when i start the machine. what is the problem. is ther any solution for the problem of the said model.

Posted on Feb 02, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 32 Answers

H4 is a fuser temp error code.

Posted on Aug 28, 2007

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Sharp Expert
  • 318 Answers

Press"#" "interupt" "c" "interupt" these 4 keys.
enter 14 , then press start Thermistor open
The thermistor is open. The fusing unit is not installed.

Posted on Dec 03, 2013

  • Abdul kasim Hazari
    Abdul kasim Hazari Apr 12, 2017

    what is the means of fusing unit can u show me in image

×

Code h4

Posted on Apr 29, 2008

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Everett Lin

  • 990 Answers

SOURCE: code H4 comes up when the sharp copier ar-5316 is switched on

Hello sir; H4 code require reset procedure as follow;
1, press"#" "interupt" "c" "interupt" these 4 keys.
2, enter 14 , then press start
3, turn power off and back on .

Posted on Jan 28, 2009

Anonymous

  • 7 Answers

SOURCE: I have a sharp copier, model AR-285, H4-01

H4 error pertains to lamp errors.

that would either be the copy lamp or the heater lamp.

check both lamps.

with heater lamps,it's usually caused by either a broken heater lamp or a dirty thermostat on the heater roller assembly.

Posted on Jun 10, 2009

Anonymous

  • 10 Answers

SOURCE: sharp ar-5316 errors

clear with CROP 14

Posted on Jul 10, 2010

Anonymous

  • 148 Answers

SOURCE: Sharp -COPIERS - AR-5316

If you go to this web page:
http://www.sharpusa.com/products/business/copiers/business_copiers_drivers/
You should be able to find the driver for that machine.

Hope that helps.
Lbcoaster

Posted on Nov 14, 2008

suhail aabed

  • 109 Answers

SOURCE: Sharp Copier AR-286 Error Code H4-01

you can remove this error by enter the sim14.

Posted on Apr 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does code: H4-00 mean


The H4-00 is a low temp error in the fuser. This can normally be reset by doing the following at the machine:

On the button panel hit
pound, star, C, star
then enter 14, hit start, then execute on the screen.

This should clear any one-off errors

www.equipmybiz.com EquipMyBiz

Aug 04, 2014 | Sharp MX-4101N Multifunction Printer Color...

1 Answer

A problemes h4-00


H4 00 - Heat roller low temperature detection - Fuser UNIT

Perform the following procedure to enter the simulation mode.
"#" key Interrupt key CLEAR key (c) Interrupt key
Main code [START] key Sub code [START] key

Main code = 14
Sub code = 00

Apr 22, 2011 | Sharp AR-5316 Advanced Digital Imager...

6 Answers

Sharp ar 5516 printers error h5. h4


hi,I have error code L h on my coppier sharp 5516. your help please.

Aug 05, 2010 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

I am getting code H4-01. What does this mean?


H4 means you have a HEAT problem, most likely a bad fuser assy.

Jan 25, 2010 | Sharp AR-407 Copier

1 Answer

Dispays h4 error


An H4 error code indicates trouble in the fusing section - a certain temperature has not been reached within a specified time. It could mean a dirty/bad thermistor or dirty/bad thermostat (both inside the fuser unit. Make sure both of these are clean and there is not debris/paper stuck inside the unit.
You can try resetting the code by : Get into SIM mode by pressing the following keys one after the other "#" "interupt" "C" "interupt" then enter 14 and the start key - confirm if requested then make sure the copier restarts.
Hope this helps.

Apr 18, 2009 | Sharp AR-5320 Black and White Copier

4 Answers

Code H4 comes up when the sharp copier ar-5316 is switched on. it cannot be use. what shall I do to solve this problem of error code H4.


Hello sir; H4 code require reset procedure as follow;
1, press"#" "interupt" "c" "interupt" these 4 keys.
2, enter 14 , then press start
3, turn power off and back on .

Jan 28, 2009 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

Code H4 is showing on the machine


h4 code in sharp .that s fuser temperature very high .just reset it.press clear key,auto photo key,clear,auto photo key.copier goes dead .when it goes dead just press 14 then start key.copier will bi ready after some time.it works.by mian jee

Dec 17, 2008 | Sharp SF 2020 Copier

1 Answer

Xerox XC 1020 copier code H4


With "H4" flashing press:
1.Clear button
2.Auto button then again

3.Clear button
4.Auto button

It should be done quickly. If it's done quickly enough all lights on display should go off.

5.Enter number 14 (as if you are making 14 copies).
6. Press START/COPY button.

The machine goes back to normal. If not, thermistor on the fuser (heater) should be replaced.

Sep 02, 2008 | Office Equipment & Supplies

3 Answers

Cant get rid of blinking error message, nothing works


The correct buttons to push in order to get into the service mode on a 162D are [#] key, [*] key, [C] key and [*] key. Then you key in 14 - 00 and press the Start key. If that fails to bring your machine back on, you'll have to replace the fusing assembly.

Apr 12, 2007 | Toshiba e-Studio162D Copier

Not finding what you are looking for?
Sharp AR-5316 Advanced Digital Imager Copier Logo

Related Topics:

1,584 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

268 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...