Question about Hitachi 46BX01B 46" Rear Projection Television

1 Answer

Hitachi 46in rear pro

Blue shadows Tried convergence red lines up both ways blue only lines up horizontally blue line is off to the far right and can not be moved left or right causing my shadows Thanks

Posted by knolekid on

Ad

1 Answer

Dewayne Turner

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

You have bad convergene output IC's. There are 2 in the set and we always replace them both because the one that s not bad will likely fail in ashort time causing you to have a 2nd labor bill.

I’m happy to help further over the phone at https://www.6ya.com/expert/dewayne_4a10eab6caecdb92

Posted on Aug 27, 2007

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Sony KDP-57WS550 TV that has a convergence problem. Based on the symptoms, I'm not sure whether to indict the convergence ICs. In the convergence mode, I can move the red (and blue) crosses,...


With your TV in setup Use a small magnet to "move" the non converged Red, Blue, or, Green color lines "crosses" (each CRT will need to be adjusted in turn) by moving the magnet close to the offending Red, Blue or,Green color CRT yoke or, tube while observing the movement of the CRT color line "cross" in a mirror ( try several places near the tube and, several strengths of magnets:) a refrigerator sheet magnet works well (you can cut these with a scissors to make a better fit or, apply less magnetic "pull." by making them smaller (you may need more than one magnet per tube to fix each CRT's convergence) When you have each CRT tube's convergence right, apply some clear silicone adhesive to the magnet and, permanently affix the magnet to the now "fixed" CRT tube exactly where you placed the magnet to obtain the best convergence on the CRT.
(Do not adjust the "Green" CRT unless you must, as it is used as the color line to adjust other lines to)

Jun 30, 2011 | Sony Grand WEGA KDP-57WS550 57" Rear...

1 Answer

Convergence Adjust


It means probably one of the two convergence ICs has blown

Jul 13, 2008 | Hitachi 53FDX01B 53" Rear Projection...

1 Answer

Convergence


did u do a repair in recent days
by replacing the convergence ICs?

Jun 18, 2008 | Toshiba 43A10 43" Rear Projection...

1 Answer

Convergence issue; red 3D effect. In grid convergence mode blue will converge w/green fixed lines and red horizontal will but the verticle red will not adjust far enough left to converge. has ajustment...


Convergence is dead.Must know how to solders?Must replaced ICS and all of it resistors.Tries Tv repair World.com,Tvrepairkits.com for a convergence kit.The shop will cost u $300 for parts and labors.

Jan 24, 2010 | Hitachi 43FDX01B TV

1 Answer

HITACHI 57UWX20B has blue ghost shadows how do I


Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projeciton sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some photos of convergence problems.

42d3683.jpg

7859b01.jpg

e87380c.jpg
Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

69189a5.pngCONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you are handy and can follow directions. You can get complete repair kits from TvRepairKits.com or click here. They have put together DIY repair kits that include the OEM parts and step by step photo instructions for each repair. If you are not handy or can't follow directions we would suggest calling a shop.

Jan 05, 2010 | Hitachi 57UWX20B 57" Rear Projection...

1 Answer

Red/Orange horizontal lines


it could be that the tv convergence circuit is going bad. One shure way of finding out is to go to the tv feature menu(picture,audio etc.) and select the customer convergence setting, you should get a cross hair pattern(cross in middle of screen). that cross should be white and by aligning the red or blue colors they should move left, right, up or down

Jul 27, 2009 | Akai PT5492S 54" Rear Projection...

2 Answers

Convergence lines are SLANTED. Red line is above


Your TV most likely a convergence failure. ( common problem )

Here are some of the most common symptoms and example photos of a convergence problem


  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
Here are some photos of convergence problems.

3dc9420.jpg
645fba6.jpg
0dcec37.jpg
Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.

0667c5f.pngSOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses. Its a fairly easy DIY job or you can call in a pro. If you want to do the repair yourself check the site www.TvRepairKits.com. Their kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, thermal paste, email/phone support, etc.

Apr 26, 2009 | Hitachi 53FDX01B 53" Rear Projection...

1 Answer

Red double picture with green and blue


convergence problem there are 2 integrated circuits inside the set needs to be replaced

Aug 25, 2008 | Toshiba TZ50V51 50" Rear Projection...

3 Answers

Fine tuning grid on my Samsung HDTV with remote.(BP59-00048)


To adjust manual convergence on your projection TV, follow theses steps:
  1. Turn your TV on.
  2. Let it warm up for 30 minutes.
  3. Press the Menu button on your remote. The Main menu appears.
  4. Use your remote to select Function, and then press the joystick.
  5. Select Convergence, and then press the joystick. The Manual Convergence screen appears.
  6. Select Red, and then press the joystick. A series of crosshairs appears on the screen.
  7. Select one of the outside crosshairs by moving the joystick up/down/right/left or by pressing the 2 (up), 4 (left), 6 (right), or 8 (down) buttons on your remote. The method you use depends on the model of remote you have. Note: You must do the outside crosshairs first.
  1. In the crosshair you selected, if you can see a horizontal red line, use the CH up or CH down buttons to move the line so that it is superimposed on the horizontal center line of the crosshair. Note: Make the single horizontal line as white as possible.
  1. In the crosshair you selected, if you can see a vertical red line, use the Vol + or Vol - buttons to move the line so that it is superimposed on the vertical center line of the crosshair. Note: Make the single vertical line as white as possible.
  1. Repeat for all outside crosshairs, and then for the inside crosshair.
  2. Return to the Manual Convergence Screen, and select Blue, and then press the joystick.
  3. Repeat Steps 7 through 10 for Blue.
  4. Press the Menu button on your remote to exit.
Important: The directions above work for most Samsung Rear Projection TVs. Yours may be different. For exact directions to perform manual convergence, see your user's manual. If you don't have your user's manual on hand, click HERE to view your manual on line.
If you cannot get your Projection TV to converge, it may need to be serviced. To arrange a service appointment, call Samsung Customer Care at 1-800-Samsung (1-800-726-7864). Have your TV's model number and serial number on hand when you call.

Jan 05, 2008 | Samsung BP59-00016A Remote Control

Not finding what you are looking for?
Hitachi 46BX01B 46" Rear Projection Television Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76287 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Todd Hill
Todd Hill

Level 2 Expert

433 Answers

Are you a Hitachi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...