Infocus Lp290 Will not stay on.

I can not keep my projector on. It will turn on and work great for a few, but then just shuts off at random times and stays off. I have cleaned the dust filters, and a new power cable but I still have the problem.

rinokeros Dec 01, 2007

I have the same problem. Additionally, I must say I noticed that before the engine turns off, the fans stop rotating. So, I assume it turns off for temperature security reasons. Any ideas? Someone told me I should install an upgrade from the official site (www.infocus.com) but I don't have the cables wanted.
Anonymous Jan 18, 2009

I had the same problem. Disassembled the projector and found no obvious reason. Read online that the power supply is weak. While using it another time, SNAP, POP and SMOKE! Took it apart again, found burn marks on the power supply board. No assistance from InFocus as their 'solution' was to buy another one.

Bulb is maybe at 20% of consumption. Terrible waste of energy, technology and materials. We do ourselves no favors through these types of business practices. Thank goodness for sites like this.

Would like to see more manufacturers recognize the long term profit incentive.

1 Answer

Anonymous

Check the area around the fan and make sure you have good airflow. Put a small fan near the unit and direct the air flow so it cools it and let us know.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

The bulb dont turn on

Projector Lamp Life and Brightness - Projector Reviews

www.projectorreviews.com/articles-guides/lamp-life-and-brightness-2/

Feb 26, 2015 - There are still a number of 2000 hours at full power projector still on the... brighter, like projector Y, but Y just doesn't have the picture quality.".

Resetting Lamp Hours on a Sharp Projector - Spiceworks

https://community.spiceworks.com/.../2235-resetting-lamp-hours-on-a-sh...

Jun 12, 2011 - However, once you change the lamp the projector still won't turn on ...If it still doesn't work then there is some other problem with the projector.

How to Repair InFocus Projector Power Issue (LP290 ...

? 1:56
https://www.youtube.com/watch?v=sPGZSJXpxqI
May 7, 2012 - Uploaded by zibodiz
A common problem with older InFocus LCD Projectors causes them to turn off at ... How to Repair InFocus Projector PowerIssue (LP290/LP280) ... How to Install a Bare Projector Lamp into your Projector - Duration: 4:05. by ..

Read full answer

Dec 14, 2015 • Office Equipment & Supplies

0helpful

3answers

Projector light turns off

lamp problem

Read full answer

Feb 01, 2008 • InFocus LP290 1100 Lumen XGA LCD Projector...

0helpful

1answer

Hello I have the infocus screenplay 5000 projector & after reading all the posts here decided I dont have a similar problem to anyone else. My bulb life expiration came up months ago but the unit works...

working with expired lamp can cause the overheat, and the power supply will be damadged, you need to replace the chemical caps at secondary parts as shown in the picture below:

Read full answer

Feb 11, 2014 • InFocus ScreenPlay 5000 Multimedia...

3helpful

1answer

Infocus X2 has discolor on the left side of image- what could this be.

the light tunnel is collapsing and will need to be replaced. you could either get the part from an infocus service center or send it to them to repair. either way, try av solutions in ny. they're really good. www.avsolutionsny.com

Read full answer

Jan 06, 2010 • InFocus LP290 1100 Lumen XGA LCD Projector...

2helpful

1answer

The device is an InFocus LP 290 with less than 100 hours on the bulb. I have used the projector several times over the course of two years without any problem, but never longer than 3 hours at a time. A...

there is an issue with the power supply edge connection with the main board. you'll need to have it sent to an infocus service center for repair. try av solutions in ny. they're pretty good. www.avsolutionsny.com

Read full answer

Nov 24, 2009 • InFocus LP290 1100 Lumen XGA LCD Projector...

0helpful

2answers

Infocus Lp240 Projector Will not power on NEW BULB. Red light Blinks on and off.

The owner's manual should have a troubleshooting chart that will indicate what the blinking lights mean. If the new bulb did not clear it, the problem may be the ballast (part that starts the bulb). Also, when you replaced the lamp, you should also reset the lamp timer. Some units will continue to indicate a lamp needing replacement until the counter is reset. The procedure for that should also be in the manual.

Keep us posted.

Dan

Read full answer

Dec 18, 2008 • InFocus LP290 1100 Lumen XGA LCD Projector...

0helpful

1answer