Question about Samsung ML 2010 Laser Printer

Open Question

Overheat fuser fuser over driving heat

Posted by dumbre goraksha on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Porcelian rollers cracking due to heat overheating


Probably not cracking due to overheating but just due to the heat of the fuser and time. The fuser can not overheat as it is protected by thermal fuses that would blow if the fuser became too hot. These roller will deteriorate over time. This is normal.

Jan 17, 2011 | Toshiba e-Studio 35 Copier

Tip

ERROR codes Canon 790


Canon 790 C No problem. Means that the machine is correcting the fuser film tracking. CC Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier. E000 Low fuser temperature E001 High fuser temperature E002 High fuser temperature E003 Erratic fuser temperature E007 Fuser film off track and will not repair itself E010 Main drive problem E030 Counter problem E064 Scan problem, or power supply E202 Scan problem E210 Lens drive problem or lens sensor E220 Exposure lamp stays on or off E240 DC controller (main board) or composite power supply E261 Zero cross problem. Power frequency or composite power supply E400 Communication problem between boards E803 24 volt problem EO Fuser problem H Fuser overheat

on Jan 19, 2010 | Office Equipment & Supplies

Tip

ERROR codes Canon 740


Canon 740 C No problem. Means that the machine is correcting the fuser film tracking. CC Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier. E000 Low fuser temperature E001 High fuser temperature E002 High fuser temperature E003 Erratic fuser temperature E007 Fuser film off track and will not repair itself E010 Main drive problem E030 Counter problem E064 Scan problem, or power supply E202 Scan problem E210 Lens drive problem or lens sensor E220 Exposure lamp stays on or off E240 DC controller (main board) or composite power supply E261 Zero cross problem. Power frequency or composite power supply E400 Communication problem between boards E803 24 volt problem EO Fuser problem H Fuser overheat

on Jan 19, 2010 | Office Equipment & Supplies

1 Answer

Had a paper jam yesterday and after removing jam screen is staing "over heat" this a a xerox workcentre pro412


"Overheat" on this machine occurs when the fuser element has over heated usually caused in jams because the paper BLOCKS the heat sensor.
Shut off your machine, wait 30 minutes to let cool off or an Hour if you have more time then re-start your copier again, if the Fuser isn't damaged the machine will reset itself. If the Problem presist then you accidentally Damaged the Fuser. If you need one Ihave those available and if your in the Connecticut area you can place a service call and we will be happy to do it.

Jul 21, 2009 | Office Equipment & Supplies

1 Answer

Diaplay shows open heat error after one print.


The fuser is overheating. Probably now has blown the overheat thermostat. You have to replace the fuser to get rid of it. Not real hard to do.

Mar 28, 2009 | Xerox WorkCentre PE16 All-In-One Laser...

Tip

ERROR codes Canon 720


Canon 720 C No problem. Means that the machine is correcting the fuser film tracking. CC Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier. E000 Low fuser temperature E001 High fuser temperature E002 High fuser temperature E003 Erratic fuser temperature E007 Fuser film off track and will not repair itself E010 Main drive problem E030 Counter problem E064 Scan problem, or power supply E202 Scan problem E210 Lens drive problem or lens sensor E220 Exposure lamp stays on or off E240 DC controller (main board) or composite power supply E261 Zero cross problem. Power frequency or composite power supply E400 Communication problem between boards E803 24 volt problem EO Fuser problem H Fuser overheat

on Jan 19, 2010 | Office Equipment & Supplies

Tip

ERROR codes Canon 6012F


Canon 6012F C No problem. Means that the machine is correcting the fuser film tracking. CC Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier. E000 Low fuser temperature E001 High fuser temperature E002 High fuser temperature E003 Erratic fuser temperature E007 Fuser film off track and will not repair itself E010 Main drive problem E030 Counter problem E064 Scan problem, or power supply E202 Scan problem E210 Lens drive problem or lens sensor E220 Exposure lamp stays on or off E240 DC controller (main board) or composite power supply E261 Zero cross problem. Power frequency or composite power supply E400 Communication problem between boards E803 24 volt problem EO Fuser problem H Fuser overheat

on Jan 19, 2010 | Office Equipment & Supplies

1 Answer

Xerox Workcentre M201 says open heat error


Fuser Error, Open Heat
Error, Heating Error and
Overheat
There is a problem in the
fuser unit.
Unplug the power cord and plug it back in. If the
problem still persists, please call for service.

Dec 09, 2008 | Xerox WorkCentre M20i All-In-One Laser...

2 Answers

I have just replaced cartridges and am now getting fuser low heat error.


Yes, either the lamp in the fuser is burnt, the thermistor (heat sensor) on the fuser is burnt, or the low voltage power supply is not providing enough voltage to the fuser lamp. Your safest bet is to replace the fuser.

BUT!!!! The printer itself is let than $150 new with warranty, so if you like this printer I would buy a new one. A fuser will be between $90 and $150 and could be difficult to replace. If you get a service person to replace it you could expect two hours of labour at least which will be about the price of a new printer.

Jun 16, 2008 | Samsung CLP 300 Laser Printer

1 Answer

Xerox 212 copier


Most likely replace the fuser.
And be sure you use transparencies marked for copiers only.
The U4 is an over heat because the tranaparency stuck between the heat roll and the thermistor. Causing the fuser to stay on and blow the overheat.

Oct 13, 2007 | Office Equipment & Supplies

Not finding what you are looking for?
Samsung ML 2010 Laser Printer Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Cindy Wells

Level 3 Expert

6220 Answers

The Knight
The Knight

Level 3 Expert

76466 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...