Drum light My drum light continues to glow after replacing the drum. Does anyone know how I can reset the copier. Thnaks

• The Drum LED continues to blink if the drum counter was not reset when you replaced the drum. To reset the drum follow the instructions below:

1. Open the front cover of the printer
2. Press and hold down Go button for about 4 seconds until al the LEDs light up. Once all 4 LEDs are lit, release the Go button.
3. Close the front cover.

http://welcome.solutions.brother.com/BSC/public/eu/eu_ot/en/faq/faq/000000/000300/000055/faq000355_007.html?reg=eu&c=eu_ot&lang=en&prod=hl2040_all

The drum counter will have to be reset, Use the following steps.

1. Open the front door.
2. Press and hold the cancel button (x button) until all the lights flash in in order.
3. Then close the front cover.

This will reset the drum counter so that you can continue to print.

common problem.

• The Drum LED blinks if the drum unit is near the end of its life. Use the drum unit until you have a print quality problem, then replace the drum unit with a new one.

• The Drum LED continues to blink if the drum counter was not reset when you replaced the drum. To reset the drum follow the instructions below:

1. Open the front cover of the printer.

1. Press and hold down Go button for about 4 seconds until al the LEDs light up. Once all 4 LEDs are lit, release the Go button.

1. Close the front cover.

Caution

Reset the drum counter only when you replaced the drum unit with a new one.

1. The Drum LED blinks if the drum unit is near the end of its life. Use the drum unit until
you have a print quality problem, then replace the drum unit with a new one.
2. The Drum LED continues to blink if the drum counter was not reset when you replaced
the drum.
To reset the drum follow the instructions below:
a. Open the front cover of the printer.
b. Press and hold down the white button for about 4 seconds until all the LEDs light up. Once all 4 LEDs are lit, release the
button.
c. Close

1. The Drum LED blinks if the drum unit is near the end of its life. Use the drum unit until
you have a print quality problem, then replace the drum unit with a new one.
2. The Drum LED continues to blink if the drum counter was not reset when you replaced
the drum.
To reset the drum follow the instructions below:
a. Open the front cover of the printer.
b. Press and hold down the white button (shown as blue in the image below) for
about 4 seconds until all the LEDs light up. Once all 4 LEDs are lit, release the
button.
c. Close front cover

Brother Drum Reset Instructions


The Drum LED continues to blink if the drum counter was not reset when you replaced the drum. To reset the drum follow the instructions below:
Press the cover release button and then open the front cover of the printer.


Press and hold down Go button until all 4 LEDs are lit. Once all 4 LEDs are lit, release the Go button.

Close the front cover.
Make sure that the Drum LED is now off.
Reset the drum counter only when you replaced the drum unit with a new one.

You have to reset the drum count on the printer after you replace the drum. Call dell tech support they will not charge you for help resetting the drum even if you are not in warrenty.

if the Drum LED is still lit after replacing the drum unit, the Drum counter may not be reset.
Reset the Drum counter as follows:

1. Open the front cover.
2. Locate the control panel button under the LED lights on the left side.
3. Press the control panel button until all lights are lit, then release it.
   The Drum counter is now reset.

You need to reset the drum count. Open the toner door. Hold the "Go" key until all 4 lights light up. Let go of the button and close the door. That should reset the drum count and stop the blinking.

Do you know the name of the MFG of the printer and maybe I can help?