Mitsubishi VS-60707 60" Rear Projection Television Logo

Question about Mitsubishi VS-60707 60" Rear Projection Television

1 Answer

Horizontal lines and screen bounce

Need to have tv on for several hours to get rid of horizontal lines and picture scroll, cant find any solutions in manual, please help.

Posted by blatzpunkgrl on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 140 Answers

You have some leaky filter caps - C2C52 = 10MFD 50 VOLT (off base of Q2C51 on signal board) also check C2P05 = 100 MFD 16 VOLT off pin #3 of IC2P01 and C2P08,C2P03 = 100 MFD 16 VOLT

Posted on Aug 22, 2007

  • Anonymous Sep 01, 2007

    OK - You need to call a TV repairman - estimated cost: $300 - $500

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How I get rid of horizontal lines

could be several reasons.
1) Loose cables
2) Defective boards
a) logic card b) TCON board 3) LED panel it self

Your TV make and model and perhaps a picture of the screen can help diagnose better

how to fix horizontal or vertical lines on lcd tv
0helpful
1answer

Why do I have rolling horizontal lines on my hitachi big screen t.v.?

Need the model number of the Hitachi which should be listed n the rear cover. I should be able to assist but will need the Model Number to determine which chassis design you have.
0helpful
1answer

Its a zenith 27in the sound is good but the picture only shows a line across the screen

Make a fist with ur hand and bang on the tv bazel frame.The tv picture flickers back or bounces back to a normal picture.The tv have a vertical or a horizontal hold ics have coldsoldering joints and requiring resoldering.If u bang on the tv bazel frame picture don't flickers back or bounces back to a normal picture.The tv have a vertical or a horizontal hold ics are dead require changes those ics chips.If u don't have all the tools.Can't do a basic soldering work or able to changes those ics chips.Shop around for tv shops for estamate and repairing prices for repairing.
0helpful
1answer
1helpful
1answer

Bright horizontal line across black tv screen

Hi There,
If your picture has collapsed to just a horizontal line across the center of the screen, this indicates that your Vertical Output circuit is bad and needs to be serviced by a qualified technician. I hope this helps and thank you for using FixYa!
5helpful
3answers

TV: bright line across black screen for several hours.

vertical output ic needs to be resoldered. careful leaving that bright line displayed on the screen as this will cause a permanent phosphor burn into the tube. this can not be corrected once burned unless you replace the tube. mch
0helpful
1answer

Erratic problem

need to have the vertical output IC pins resoldered.
0helpful
1answer

Horizontal lines and screen bounce

These sets have capacitors that will go bad, but without a good ERS meater that tests these in curcuit you could be spending a lot of time doing nothing, But the most common is to find the 9 volt reg on the signal board and change all within a 2 inches of that regulator
Not finding what you are looking for?

177 views

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76839 Answers

Ekse

Level 3 Expert

13435 Answers

Cindy Wells

Level 3 Expert

6470 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...