Question about Hotpoint Aquarius WD63 Front Load Washer/Dryer

1 Answer

The dial keeps getting stuck and the washing programme can't continue

When the machine is switched on, it takes in water but the dial appears to "stick" and the programme does not procede. I have tried to move the dial "gently" to the next position but it does the same and won't move any further. Then it wouldn't spin when I set it to that position. It just sounds like it is emptying out. To make matters worse, when the dial reaches stop, it blows the trip switch on the mains switchboard for the house. Please if anyone has any tips, they would be a great help, before I turn it into a tin can!!!

Posted by on

Ad

1 Answer

Sounds like motor is faulty. Regards Advisor

Posted on Aug 22, 2007

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Programmer stops at no 2


I would get a quote off the washing machine repair person as the fault could be any where in the system eric

Jan 14, 2018 | Washing Machines

1 Answer

How do i reset washing machine AEG 64840


You can choose the right programme for any type of laundry following the descriptions on the washing programme tables (see «Washing Programmes»).
Turn the programme selector dial to the required programme. The programme selector determines the type of washing cycle (e.g. water level, drum movement, number of rinses) and the washing temperature according to the type of laundry.
The pilot light of button 8 starts blinking.
The selector dial can be turned either clockwise or anticlockwise. Position "0" to Reset programme/ Switching OFF of the machine.
At the end of the programme the selector dial must be turned to position "0", to switch the machine off.
If you turn the programme selector dial to another programme when the machine is working, the yellow pilot light of button 8 will blink 3 times and the message Err is displayed on the display to indicate a wrong selection. The machine will not perform the new selected programme.

Dado

Jan 15, 2015 | AEG Washing Machines

1 Answer

Indesit 657w


CHECK TO SEE IF THE DRAIN HOSE IS RAISED ABOVE THE REQUIRED HEIGHT. IF THE WATER IS OVER FLOWING THE TUB THEN IT IS USUALLY THE A BLOCKAGE IN THE PRESSURE SWITCH HOSE, OR SOME INABILITY OF THE WATER LEVEL SWITCH TO MEASURE THE AMOUNT OF WATER IN THE TUB.

Dec 23, 2013 | Washing Machines

1 Answer

Error code 07 on my Aqualtis AQXXF


Might be a bit complex but this is your problem and solution

REMEMBER TURN THE POWER OFF

F07: Heater relay stuck or element open circuit
This fault is only signalled when pressure switch is in empty position.
Check the efficiency of edge connector J3 on module.
Check wiring to heater and continuity of element (25 ohms approximately).
Check the efficiency of pressure switch connections and correct operation of pressure switch,
and the pressure chamber is not blocked with sludge.
Remove edge connector J3 and check wiring and contacts at positions 2, 3 and 4 on J3.
If all above OK replace pressure switch, module or eeprom as required.

Jun 10, 2009 | Washing Machines

1 Answer

Washing machine will not drain


TAKE THE HOSE OFF ON THE BACK {DISCHARGE HOSE} IF THE WATER FLOWS OUT IT IS THE PUMP MOTOR IF IT DOESN'T THERE IS SOMETHING BLOCKING THE OUTLET, SMALL CLOTHING ITEM

May 29, 2009 | Indesit W 123 Front Load Washer

1 Answer

Programme gets stuck on wash cycle


Most likely a defective door switch.

Mar 02, 2009 | Washing Machines

1 Answer

My indesit washer/dryer model w10 ,is not working.the programme dial keeps cliking round wont start a programme or take in water.


probably a main module fault but worth while checking for continuity thro the heater and that the pump and filter are ok. the idea is that when a fault is detected, the dial will click round indicating a fault but usually it is the module itself. expensive part. not worth repair

Jul 04, 2008 | Indesit Washing Machines

1 Answer

Washing machine keeps taking water in even after programme has stopped


poss moisture on your control module causing tracking . unplug your machine from the mains and take the back panel off, you can try blowdrying the module down in the bottom left hand corner or you can take it off (noting where all the leads go to),get an old toothbrush and clean the solered side around the bottom of the board failing that you will most probably have to change it

Jul 07, 2007 | Indesit WA 115 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WD63 Front Load Washer/Dryer Logo

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

Eric Taylor

Level 3 Expert

590 Answers

Richard C Cohen
Richard C Cohen

Level 2 Expert

157 Answers

Onofrio Taverna
Onofrio Taverna

Level 1 Expert

12 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...