Radio does not come in and hold the radio siglen

Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. 5. To exit, press any button/knob or wait five seconds http://www.chryslercommercialvehicles.com/jeep/download/pdf/manuals/2014-Patriot-OM-1st.pdf page 240

Make sure your car is in the "ACC" or "ON" position, and hold down the "TIME" button on the face of the radio until the time starts blinking. Press "TIME" until the hours start blinking, then use the "TUNE" knob to change the hours. Press the "TIME" button once more to change to minutes, and use the "TUNE" knob to change the minutes once they have started blinking. Afterwards, press any other button on the radio to exit programming mode. Hope this helps!

To set the Alarm 1 time - On the control panel, hold down ALARM
SET and press TUNING up or down. The time display changes slowly at
first, then more quickly. Release TUNING to stop.
On the remote, press TIME. The ALARM indicator flashes. Press
TUNING up or down. The time display changes slowly at first, then
more quickly. Release TUNING to stop. Press TIME to return the display
to the current time.
To turn on the Alarm 1 function - Press ALARM MODE or
ALARM in sequence to select the mode you want: tone, radio,
both tone and radio, or off.
For tone only, press until the indicator lights.
For radio only, press until the indicator lights.
For tone and radio, press until both indicators light. When the
alarm goes off, the tone sounds. Press SLEEP/SNOOZE to turn the
radio on. Press SLEEP/SNOOZE to pause the radio for 10 minutes.
To turn off the Alarm 1 function - Press ALARM MODE or
ALARM until the display shows no Alarm 1 mode indicators.
To check the Alarm 1 setting - On the control panel, hold down
ALARM SET to see the wakeup time.
On the remote, press TIME to see the wakeup time. Press TIME again to
return the display to current time.
To wake to a preselected radio station with Alarm 1 - While
holding ALARM SET, press the PRESET button for the station you want
(change between AM and FM if needed).

I have an 02 Santa Fe with 5064 radio. Here is what works for me. Key to ACC.
PWR on radio to OFF (display time only).
Press & hold { 4 D- } & { DISP } button simultaneously for about 3 seconds. Time will blink. If time does not blink, turn key to OFF, back to ACC & start over.
With time blinking....
Press { TUNE/SEEK UP } (double arrows) button to get desired hour.
Press { TUNE/SEEK DOWN } (double arrows) button to get desired minute.
Once set, wait a few seconds for time to stop blinking & your done.

Hi,
Srt HOLD switch to Off position as shwon in below image so Radio will start work.
Thanks.

if you have preset buttons dial up your station and hold down the selected button until the number stops flashing

First things first, if you havent already done so, check the owners manual. If you lost it or dont have one, i suggest 1 of these 2 procedures:

1.) Next to the radio, there should be 2 little holes. They are actually buttons. One of these has hours or "h" above it, while the other is labelled minutes or "m". Use a pen to press those little buttons to set the correct time.

OR

2.) Use the knobs to tune the radio (AM/FM and volume) to set the time. This is how it works:

-Press and hold the Time button
-The "hours" on the display should flash
-Turn the radio tuning knob to set the correct time
-Press and hold the tuning knob
-The "minutes" on the display should flash
-Set the correct time

Then you should either wait for it to stop flashing or press the time button to set it.

Setting Time
1 Press TITLE repeatedly until the time is displayed.
For details, see “Displaying the Text” (page 13)
2 Press and hold TITLE for at least 2 seconds while
the time is displayed.
The time indication will blink.
3 Turn the Rotary encoder to adjust the hours while
the time indication is blinking.
4 When the hour has been adjusted, press MODE.
5 Turn the Rotary encoder to adjust the minutes
while the time indication is blinking.
The time is automatically set 5 seconds after the minute
adjustment. The time can also be manually set by pressing TITLE.
• To synchronize the clock to another clock/watch or radio time
announcement, press and hold MODE for at least 2 seconds after
setting the “hour.” Minutes will reset to “00”. If the display shows
over “30” minutes when you do this, the time will advance one hour.
Listening to Radio
1 Press SOURCE/POWER until a radio frequency
appears on the display.
2 Press BAND repeatedly until the desired radio band
is displayed.
F1 (FM1) F2 (FM2) AM F1 (FM1)
3 Press TUNE to select the tuning mode.
DX SEEK (Distance mode) SEEK (Local mode)
OFF (Manual mode) DX SEEK
• The initial mode is Distance mode.
Distance mode:
Both strong and weak stations will be automatically tuned in
(Automatic Seek Tuning).
Local mode:
Only strong stations will be automatically tuned in (Automatic
Seek Tuning).
Manual mode:
The frequency is manually tuned in steps (Manual tuning).
4 Press or to tune in the desired station.
Holding down or will change the frequency
continuously.
Manual Storing of Station Presets
1 Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
2 Press and hold, for at least 2 seconds, any one of the
preset buttons (1 through 6) into which you wish
to store the station.
The selected station is stored.
The display shows the band, preset number and station
frequency memorized.
•You will need to start from set up or you will not be able to set the mins

I emailed the company and they sent a pdf of the manual back the same day.

[email protected]

The radio is analog with a digital display. Mine displays off all the time, you can try turning the other switches on it just slightly. Just move them a tiny amount. This seems to correct my problems. Heat is also another factor with these things, they drift all over the place.