Question about Fuzzbuster F4000 Radar Detector

1 Answer

Broken Display I have had this detector for a few years now, and it continues to work well for me. My problem is that the text display doesn't work. I still hear the beeps and bloops from it, but it no longer shows the band (X,Ka, etc.) or the bars to tell me how close it is. Thing is, when I press down on the top of the unit, the text appears as long as I am applying pressure. Is there a way to fix this so I don't have to press down to get a display? Any help would be greatly appreciated.

Posted by BiscoRoc on

Ad

1 Answer

John Nolan

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Whistler Expert
  • 347 Answers

Sorry but Fuzzbuster is not a Whistler Product but manufactured by Fuzzbuster which i beleive is no longer in business.

Posted on Feb 11, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What is the difference between the Whistler XTR 265 and the xtr438

The XTR-438 has Text display (vs. the XTR-265 Icon display), filter and TFSR modes (TFSR = Traffic Flow Signal Rejection). This mode helps reduce the alarms from traffic monitoring transmitters.
0helpful
1answer

Radar says cal???

There is no text display on a 1640 also this model doesn't have voice capability. Now, in order for the compass to properly function the unit does need to be calibrated. There is a sticker on the bottom of the unit that gives step by step instructions.
0helpful
1answer

Doesn't display time of text's

Texts time display is normally set by the network
0helpful
2answers

I hav3e a Whistler 1765 unit and when I tried to transfer it to a new car it would not calibrate, even after 5 tries. It was "stuck" on 315 degrees. Then the display changed and was stuck on...

There could be few reasons for this.
1. There is strong magnetic field near the radar detector. This could be even car speakers.
2. There is power lines going above the place where you are trying to calibrate.
3. To complete calibration you need to press both the volume control buttons while the vehicle is parked.. The display will show "CAL MODE". Then slowly drive at least 2 complete circles while in calibration mode. Then again press both the volume control buttons for 2 seconds until it beeps and shows " CAL DONE" in the display.
0helpful
1answer

Previous homeowner turned off GE Spacesaver 2.0 microwave display and now we can't turn it back on. Tried directions given to press option button 5 times then #1 to turn display back on. Doesn't...

I was not aware you could turn off the display, maybe it is just a bad display and you need to replace the board??!!
Ive been repairing Microwaves for 37 years. i do not remember seeing one where you could just turn off the display.
0helpful
1answer

Please help.. my monitor has no display and my don't even beep. the LED in the monitor turns back to orange after few seconds. cpu, disk drives and ram are working..

This is one of the serious problem that arises because if you set your monitor with a high resolution with high frequency, then the monitor doesn't display anything as it's frequency is out of the rang or limit of the monitor's actual resolution capacity. Each monitor will have a limit of max frequency that is said to be the Refresh rate (for each and every resolution setting the display is refreshed.) When high resolution is set with high frequency that is not supported by the monitor, it then display a message like "frequency out of range". If you press ESC key within the few seconds of this setting, it will revert back to its initial resolution. But if you continued with the setting of same High resolution with High frequency, the monitor is not going to display anything because its frequency is out of the range. Most of old monitors like CRT's etc doesn't support 1024×768 at a refresh rate greater than 60Hz.
8helpful
3answers

How long does the nighthawk model carbon monoxide detector last for.

I had 2 and they both did the ERR thing and stopped working within a week of each other and that was about 7 years.
1helpful
3answers

Periodically emits 3 loud beeps. Displays 888.

The CO detectors require replacement of the battery periodically.

Unlike smoke detectors, the detector element itself also requires replacement as well as the battery and is sold as a module with the battery attached.
0helpful
1answer

Display won't light

This is most likely due to a cold solder joint for one of the display leads where they are soldered to the edge of the circuit board. Or, possibly, the display itself has gone bad.
0helpful
4answers

Probem with XRS 9675 Detector

the text display connection to board, not connected. take apart and re attach
Not finding what you are looking for?
Fuzzbuster F4000 Radar Detector Logo

Related Topics:

104 views

Ask a Question

Usually answered in minutes!

Top Whistler Vehicle Parts & Accessories Experts

Brad Brown

Level 3 Expert

18686 Answers

Ngoro

Level 3 Expert

3180 Answers

ray gallant

Level 3 Expert

72651 Answers

Are you a Whistler Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...