Question about Winsource Tech Solutions TS-4500 Cross-Cut Shredder

1 Answer

Fellowes DM8C Shredder

Power comes on but machine dosen't kick on. Little temp light is on too. What's the deal? I guess there is a fuse somewhere. Does anyone know what type and where it's located? I took the top off to see if anything was jammed but nothing. Thanks, Susan

Posted by susan10 on

  • stevehello Jan 09, 2008

    I have the same problem. I removed the 6 screws that holds it togather but, it won't come apart. Does anyone know how to take this apart so that I can fix it?

×

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 102 Answers

For user susan10 if you have a Fellowes machine I suggest you call customer service at 1-800-945-4545

For user stevehello check under stickers or any plugs for any hidden screws some shredders are also put together with tabs that need to be pried apart but check for hidden screws first.

Posted on Mar 02, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gibson gas furnace


Check the flame sensor is clean and the connections are tight . check air filter is clean , also check the afc is clean at the back .

Jun 21, 2017 | Heating & Cooling

1 Answer

85 corolla ae82 sedan 5 speed... I'm not getting


do you have freon in the system because the low pressure switch will not let the compressor run with out enough freon dont know where the switch is but it should be near the dryer there is also a diode in the harness going to the compressor

Aug 12, 2013 | Cars & Trucks

1 Answer

Maybe a leak?


sounds like a faulty oil light sender that has a leak or has blown. Will drain sump verry quickly

Dec 10, 2012 | 1995 Chevrolet Camaro

1 Answer

On my nissan murano one of the radiator fan dosen't work passanger side


I'm not sure if the Murano is this way, but several vehicles have staggered fans. One fan works when the temp gets to a certain level, then if the temp goes up more, the other fan kicks on.

Try running the A/C and see if both fans operate, and give it some time to allow the temperature to climb. Don't let it get past 3/4 on the temp gauge though, if you are experiencing overheating.

Jun 07, 2012 | 2003 Nissan Murano

1 Answer

Heater light kicks on but pump doesn't come on, then soon, the heater kicks off


Without knowing what equipment you have, I would guess that ypu have a defective pressure or flow switch. This would allow the heating circuit to activate without adequate water flow. The temp builds up in heater assembly which triggers the high limit switch to kill circuit until it cools down.

Aug 10, 2009 | Pool & Spa

3 Answers

96' Cavalier coolant light on, replaced thermostat, fan not on


sound like your coolant temp sensor runs your fans.

Aug 07, 2009 | 1996 Chevrolet Cavalier

1 Answer

2003 ford expedition , missing while accelerating


most likely cause is a defective ignition coil, there is one for each cylinder (coil over plug), the dealer will have to test it to determine which of the eight coils is the source of the miss. the coils are about $60 each

May 20, 2009 | 2003 Ford Expedition

7 Answers

Hi, my simpson eziset 550 washing machine wont start, I press power on then the start button and beeping alarm starts with the three water temp lights flashng, this has happened intermitantly in the past...


5 beeps with the 3 temp lights flashing means lids not closed. or lid switch not working

i just fixed this problem. the magnet in the lid had come loose. I undid the two screws on the side of the lid put the magnet back where it should sit then i poured candle wax over it to hold it in place and working fine now.

Nov 30, 2008 | Washing Machines

1 Answer

My dryer had a power surge and kicked out my circuit breakers out twice. My light in my dryer went out. The light is located on the top of the opening of the dryer. I replaced it with a new bulb, but it...


depending on your dryer make and model, you may have a thermal limiter or a high temp fuse that went out. Also, you may need to look into new thermostat for it. If I had the make and model of the dryer, I'd be able to be more specific.

Mar 16, 2008 | Dryers

Not finding what you are looking for?
Office Equipment & Supplies Logo

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Winsource Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2239 Answers

Ekse

Level 3 Expert

13434 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Winsource Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...