Question about Garmin StreetPilot 2620 GPS Receiver

2 Answers

Garmin streetpilot 2620

St. pilot in following loop at power on. - logo - safty warning - back to logo Will reloading street data file fix? thanks John

Posted by redbaron1966 on

  • 440rt Apr 05, 2008

    Same thing here. I really don't like my Garmin because really never worked that great and now this. Getting tired of fixing. [email protected]

  • Anonymous Apr 12, 2008

    St. pilot in following loop at power on.
    - logo
    - safty warning
    - back to logo

×

Ad

2 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

Hold down Menu-Find buttons if you get this screen, your hard drive gone bad. Garmin charges $275 to replace your unitGarmin streetpilot 2620 - 8863097.jpg

Posted on Apr 01, 2008

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have the same problem let me know if you find a solution, I called garmin and 1 tech told me to try holding down the page and menu buttons down together while turning unit on , but it didnt fix my problem if you get a solution let me know [email protected]

Posted on Aug 25, 2007

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a reset button on the lg leon


There is, a BIG one and a SMALL one.

Soft Reset, Press and Hold the Volume Up button and the Power button until the logo appears and release. The wakes up an reloads a frozen phone.

Hard Reset, Press and Hold the Volume Up button and the Power button from a powered down phone and keep holding until the Recovery Console appears, and follow the prompts and warnings. This clears everything off the phone to it brand new state, all personal data gone.

Dec 19, 2016 | LG Cell Phones

1 Answer

Raypak rp 1200 - pilot is on, unit will not fire. 10-12 ohms in safety loop. 340 ma from generator with loop connected. 440ma with loop disconnected. Do I need to clean the generator/pilot orfice? If...


If this is a MV heater you need 500MV to run the heater. 200 to start the pilot and 300 to open the main valve. If your dropping 100MV on the safty circut you will need 600 or better to fire the heater. I would clean all the connections on the safty circut. I will usually change the whole pilot assembly, but you can get away with just the pilot generator.
It's hard to say how to remove the pilot as their are a couple of different ones and the heater you have listed has none, but a hot surface ignitor instead. Also it runs on 110 or 220v stepted down to 24v for most of the safty circut.

Sep 04, 2010 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

When trying to sync, error message reads (sys 0505)(0,841).What can I do? For Palm TX handheld


Hi,
Try to perform a System Reset (see article linked below). If it works to break the loop, you should then be able to delete the offending "My Palm" software and perform a Hotsync to backup your data to your desktop.

If that doesn't break the loop, you'll have to perform another Hard Reset. Sometimes, a Hard Reset takes a couple of tries to get it right, since it's easier to do it wrong than to do it right.

This article discusses the various types of Reset for different Palm devices:

http://tinyurl.com/zlwza

Until you break the TX out of its loop, you won't be able to get the data from it.

To see the Palm OS version running on your TX, enter the Menu, select Info, then Version.


To Get Out Of A Loop:
  1. Perform a SYSTEM RESET by doing the following:
a) Press the UP Button
b) And THEN press and release the RESET Button
c) When you see the second Logo (Palm Powered) release the UP Button
d) Now check if your SYSTEM RESET worked by going to Beam Receive. If it goes back to Off even after you put it to On it means you were successful

2. Now Perform A SOFT RESET by pressing and releasing the button in the back once

  1. After a soft reset, a logo screen appears, followed shortly by a Preferences screen asking you to set time and date.

  1. If a soft reset does not break it out of the loop, you may need to try one of the other resets below.

  1. Do an INCOMPLETE HARD RESET by holding down the power (on/off) button on your device.

  1. While holding down the power button, Press and release the reset button on the back of your handheld device

  1. Keep the power button pressed and release it when the “Palm Powered” logo appears.

  1. A message will now appear warning that you are about to “Erase All Data”. And this will happen if you press UP or DOWN.

  1. Instead you press left or right to begin a soft reset, leaving your data intact.

  1. Your device will then take you through a series of screens to calibrate the digitizer and verify the time and date.
Sorry this was so long, I tried to put everything down that might help you.

Aug 03, 2009 | Palm TX Handheld

1 Answer

Forgot my palm pilot password


You will need to do a hard reset...this will wipe all the data and reset it back to factory specs...

1...While holding the power button, use the tip of the stylus (or a similar object
without a sharp tip) to gently press and release the reset button inside the hole
on the back of your handheld.
2... Wait for the Palm Powered™ logo to appear, and then release the power button.
3... When you see the message that warns you about erasing all of the info on your
handheld, do one of the following:

• Press Up on the 5-way navigator to finish the reset and show the touchscreen.
• Press any other button to do a soft reset.

Jan 11, 2009 | Palm Z22 Handheld

1 Answer

My Street Pilot C330 will not navigate pass the where to/view map screen Screen seems to be frozen


I have a c340 and instructions say: if your unit locks up. press the power button to turn off the unit, then press again to turn unit back on. If this does not help, reset by the following: place your thumb nail in the groove located under the Garmin logo on the face plate, gently pull off the face plate, press the reset button, turn the unit back on and it should operate normally

Dec 27, 2008 | Garmin StreetPilot C330 GPS Receiver

4 Answers

Constent reboot - flashing Access Powered


There is a soft/warm reset which bypassed the loop without losing your data.  press the up key and reinstall your battery.  do not let go until the palm screen fully loads. when fully reloaded let go.  sounds a little confusing but the palm website has step by step instructions.

Sep 24, 2008 | Palm Treo 755p Smartphone

2 Answers

Wont pickup satellites


WARNING: This will erase ALL user data on the device. You'll have to re-enter your custom addresses, etc...

To erase all user data on the device, please follow these steps:
  1. With the unit turned off press and hold the thumb wheel down, then press the back arrow and hold down, then press the power button.
  2. When all 3 are held down a message will appear that reads "DO YOU REALLY WANT TO ERASE ALL USER DATA". Select "Yes".
  3. Let go of the buttons and go through the reset sequence. The unit will need to sit outside to acquire satellites.

Nov 21, 2007 | Garmin StreetPilot i3 GPS Receiver

2 Answers

HELP


Probably an incompatible app you recently installed. Try deleting the app. If all else fails, you might try doing a hard reset. Make sure your data is backed up since a hard reset wipes out ALL data.

Nov 18, 2007 | Palm Treo 755p Smartphone

1 Answer

Garmin Street Pilot i5 Stopped working all of a sudden


Resetting Your StreetPilot
If your StreetPilot freezes (stops responding to button presses), try turning it off and then on again. If this does not help, remove the batteries and then reinsert them. Disconnect from external power, if necessary.
Clearing all User Data
If resetting does not fix your problem, you may need to clear all user data from your StreetPilot.
• IMPORTANT: zf you clear all user data, you will delete all saved locations from My Favorites I and all settings in your StreetPilot. Be sure you want to clear all user data before proceeding.
To clear all user data, press and hold down all buttons in the following order: ciJ, Wheel, Power.
Continue holding down all buttons until you see a prompt, “Do you really want to erase all user data?”
Select
Yes.

Nov 16, 2007 | Garmin StreetPilot i5 GPS Receiver

Not finding what you are looking for?
Garmin StreetPilot 2620 GPS Receiver Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garmin GPS Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

John Egan
John Egan

Level 2 Expert

85 Answers

Janelle Schoonover
Janelle Schoonover

Level 3 Expert

842 Answers

Are you a Garmin GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...