Bad color The color is totally off...seems to be all tinted in shades of green

Where you tinting / coloring over a existing color?
It is real important that you navigate / calculate what your natural color level and what natural reflect your hair is. (Not artificially from a previous tint) Because tint is not total matt coverage like paint. Hair color wont tint over tint accurately. This is how many horrific bad colors are born.
If your eyes are blue or hazel & you have a fairer complexion that color is more feasible. If your eyes are brown and your hair is medium to coarser texture and very dark its a lot more complicated because you could throw scaling down (backwards) from lots of red to brassy copper to gold.
The actual formula needed is calculated on how many shade levels of lift counteracted by what reflect your lightened hair will throw. Not necessarily by what color the tint box says. The color shade on the box is a idealistic situation. If your having trouble following me or these complexities cut about 50 strands of hair at the nape (back of neck underneath your hair and put scotch tape around it. Then mix a minute amount of color and developer and you will understand me. This way you can at worse only screw up of 50 strands of hair (instead of everything attached to your head). Bad hair color jobs are expensive to fix & as I can see what we are working with a guess is a hazard. Don't take on almost mission impossible blindly.

It is real important that you navigate / calculate what your natural color level and what natural reflect your hair is. (Not artificially from a previous tint) Because tint is not total matt coverage like paint. Hair color wont tint over tint accurately. This is how many horrific bad colors are born.
If your eyes are blue or hazel & you have a fairer complexion that color is more feasible. If your eyes are brown and your hair is medium to coarser texture and very dark its a lot more complicated because you could throw scaling down (backwards) from lots of red to brassy copper to gold.
The actual formula needed is calculated on how many shade levels of lift counteracted by what reflect your lightened hair will throw. Not necessarily by what color the tint box says. The color shade on the box is a idealistic situation. If your having trouble following me or these complexities cut about 50 strands of hair at the nape (back of neck underneath your hair and put scotch tape around it. Then mix a minute amount of color and developer and you will understand me. This way you can at worse only screw up of 50 strands of hair (instead of everything attached to your head). Bad hair color jobs are expensive to fix & as I can see what we are working with a guess is a hazard. Don't take on almost mission impossible blindly.

Hi Lizzette,
I am afraid your problem is a little technical. Well if you know something about lcd tv technicals, the problem seems to be the T Con board and/or its connectors. Check the ribbon cables and connectors, clean them properly and and start the tv.If it is not possible or it does not work, please consult someone qualified to handle your set. Good luck.

Go to menu then color ,Tint adjust the tint if that does not clear picture then you have Bad Lighht Engine Encompass parts Distribution might have it go to their website and type in your model number 1-800-638-3328

I always look for Parts on Ebay find better deals their sometimes.
UED might have it also 1-800-648-6657

Go to menue on controller, then Picture, then adjust Color and Tint to you taste. The color ajusts Blue and Green move left more blue move the slider right more green. The Tint controlls red. More red move right less left. Also chech Color temp setting.

Possibly it is running low on Blue ink - because colors are usually a mixture of inks - for example green is made from blue and yellow - if an ink runs low it will print the available colors or substitute the next available color.Probably if it prints green yellow - then it has no blue available to make the right shade.

I had similar problem: everything muted and with brownish tint. Tried everything, finally discovered that I installed wrong cartridge: 6PC instead of 6C. The "photo" cartridges are pretty much the same, make sure you have the right ones: 6C, 6M, and 6Y.

Picture Menu
Picture Mode: Expert1
*Backlight: 16
*Contrast: 83
*Brightness: 53
Sharpness: 50
*Color: 55
*Tint: 0
Expert Control

• Fresh Contrast: Off
• Noise Reduction: Medium
• Gamma: Medium
• Black Level: Low
• Real Cinema: On
• TruMotion: Low
• Color Standard: HD (N/A w/HDMI)
• White Balance: Warm
• **Method: 10-Point IRE
  • 10 IRE
    • **Red: 1
    • **Green: 2
    • **Blue: -16
  • 20 IRE
    • **Red: -6
    • **Green: 0
    • **Blue: -7
  • 30 IRE
    • **Red: -5
    • **Green: 0
    • **Blue: -4
  • 40 IRE
    • **Red: -8
    • **Green: 0
    • **Blue: -4
  • 50 IRE
    • **Red: -4
    • **Green: 4
    • **Blue: -4
  • 60 IRE
    • **Red: -6
    • **Green: 6
    • **Blue: -5
  • 70 IRE
    • **Red: -8
    • **Green: 3
    • **Blue: -10
  • 80 IRE
    • **Red: -8
    • **Green: 7
    • **Blue: -16
  • 90 IRE
    • **Red: -9
    • **Green: 5
    • **Blue: -18
  • 100 IRE
    • **Red: -10
    • **Green: 4
    • **Blue: -9

Color Management System

• Red Color: 0
• Red Tint: 0
• Green Color: 0
• Green Tint: -15
• Blue Color: 0
• Blue Tint: 11
• Yellow Color: 15
• Yellow Tint: 2
• Cyan Color: -15
• Cyan Tint: 0
• Magenta Color: 0
• Magenta Tint: -1

lg70 nice tv excellent processor just to bad there is no intensity control on color management oh well still better than what the three s are pushing block out the hype lg will be number 1 in a few years haters are starting to come around and well leds coming,

p.s. i dont work for lg just tired of losers bashing stuff because they dont own it.
im isf certified those settings are right on the money straighter than a ruler

Try adjusting your TINT control in the menu.

IF the problem seems to be in a surtan area of the screen, the light engine is bad. This is very expensive to fix. You might want to buy a new tv.

Sounds as if one or more colors is out/dry in the ink cartridge. Have you tried a new cartridge or cartridges?