Zanussi ZWF1430W Front Load Washer Logo

Question about Zanussi ZWF1430W Front Load Washer

2 Answers

Zanussi zwf1430s error codes - E40 / E41 & ELE

Had error code E40 - found out that this is either the door interlock or main pcb (EEK!)
Did a little more research and managed to get another code displayed of E41. Achieved this by holding down the start/pause button & skip buttons together, then switched machine on. Leds then flashed around the display board. Can't remember what I did next, but got a code of ELE in the display?
Any ideas what this means?
Many Thanks
Tracy

Posted by traloumar on

  • Adrian Mole Mar 24, 2009

    Earlier I went to put the washing on and the error code E40 appeared, I pressed start and kept making this 'clicking' noise and then would stop and the code appear. Came on internet and typed in 'Zanussi washing machine E40'. On different help sites it said E40 could be the door so I went down again, turned it on, slammed the door and pressed start and it started working. Hope that's all it is.

×

Ad

2 Answers

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 44 Answers

Hi

ele means the pcb is in factory settings . all you need to do is turn back off the on again then will be back to normal use. but e41 usally means the door lock has failed. does it click alot when you start it up and not do anything? if so this will be the lock

regards

Posted on Mar 21, 2009

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Hi i have a Zanussi zwf1430s and the power button has turned to a faint orange instead of the normanl green light, Also the door has locked itself with a load in !!!! any ideas ?

Posted on Aug 11, 2010

Ad

3 Related Answers

Anonymous

  • 96 Answers

SOURCE: Zanussi ZWF1437W washing machine - wont start

The error message "Err" usually indicates that the wash program and option are not compatible. 40 degrees and 900 rpm Spin should be o.k.. I would try another wash program with no special options and see if the problem goes away.

Posted on Mar 07, 2008

Anonymous

  • 35 Answers

SOURCE: error`E40

hi there e40 fault is a problem with your door interlock. get it replaced and all will be fine..

Posted on Apr 04, 2008

Anonymous

  • 1 Answer

SOURCE: Zanussi Electrolux ZWF 1430 W (E20 error)

Check water "forreign object trap". It's under the lid at the bottom of the machine. First drain water by pulling out the hose and pull out the plug. Then unscrew the trap. Have had this E20 error twice. First it was two coins there, next it was a big paperclip. Have worked fine ever since.11_20_2011_8_57_27_am.jpg

Posted on Nov 20, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Showing on screen E41

Family error code E40 is visible to customers and (could be E41,E42,E43,E44 and E45 only visible in service mode) means problem with open door or door interlock.
I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and the nearest option button simultaneously for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the alarm.
The alarm sequence continues as long as the two buttons are held down.
E41 - Door open
E42 - Problems of door closure
E43 - Interlock power supply triac faulty
E44 - Door interlock sensor faulty
E45 - Door interlock sensing circuit triac faulty

Possible causes:
Door interlock faulty, wiring faulty or PCB faulty.

Dado
0helpful
1answer

EWF 1704 erro 41

Family error code E40 is visible to customers and (could be E41,E42,E43,E44 and E45 only visible in service mode) means problem with open door or door interlock.
I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and the nearest option button simultaneously for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the alarm.
The alarm sequence continues as long as the two buttons are held down.
E41 - Door open
E42 - Problems of door closure
E43 - Interlock power supply triac faulty
E44 - Door interlock sensor faulty
E45 - Door interlock sensing circuit triac faulty

Possible causes:
Door interlock faulty, wiring faulty or PCB faulty.

Dado
0helpful
1answer

My zanussi washer is coming up with error code 40 anyone no what it is

Family error code E40 is visible to customers and (could be E41,E42,E43,E44 and E45 only visible in service mode) means problem with open door or door interlock.

Dado
0helpful
1answer

How to do with E40 code of Electrolux EWF 1074?

Family error code E40 is visible to customers and (could be E41,E42,E43,E44 and E45 only visible in service mode) means problem with open door or door interlock.
I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and any of the option buttons for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the alarm.
The alarm sequence continues as long as the two buttons are held down.
E41 - Door open
E42 - Problems of door closure
E43 - Interlock power supply triac faulty
E44 - Door interlock sensor faulty
E45 - Door interlock sensing circuit triac faulty

Possible causes:
Door interlock faulty, wiring faulty or PCB faulty.

Dado
0helpful
1answer

Jet stsem no water comming in and flahing erreor 40

Family error code E40 is visible to customers and (could be E41,E42,E43,E44 and E45 only visible in service mode) means problem with open door or door interlock.
I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and any of the option buttons for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the alarm.
The alarm sequence continues as long as the two buttons are held down.
E41 - Door open
E42 - Problems of door closure
E43 - Interlock power supply triac faulty
E44 - Door interlock sensor faulty
E45 - Door interlock sensing circuit triac faulty

Possible causes:
Door interlock faulty, wiring faulty or PCB faulty.

Dado
0helpful
1answer

Turn on my jet system 1200 fj 1254w xc just makes clicking sound

Obviously appeared family error code E40 (visible to the customer) what means a problem with door interlock. Could be: door open (mechanical failure), door interlock malfunction, the problem with main PCB (triac) or wiring. In service mode you can see exactly error code: E41,E42,E43,E44 or E45.

Dado
0helpful
1answer

Error code E40 on a Electrolux Front Loader Washing Machine EWF1090 What does it mean and how can I fix it?

Family error code E40 is visible to customers and (could be E41,E42,E43,E44 and E45 only visible in service mode) means problem with open door or door interlock.
I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and any of the option buttons for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the alarm.
The alarm sequence continues as long as the two buttons are held down.
E41 - Door open
E42 - Problems of door closure
E43 - Interlock power supply triac faulty
E44 - Door interlock sensor faulty
E45 - Door interlock sensing circuit triac faulty

Possible causes:
Door interlock faulty, wiring faulty or PCB faulty.

Dado
0helpful
1answer

AEG Lavamat washing machine model 76850, shows a blinking key and makes clicks and after that shows E40. Thanks John

Family error code E40 is visible to customers and (could be E41,E42,E43,E44 and E45 only visible in service mode) means problem with open door or door interlock.
I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and any of the option buttons for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the alarm.
The alarm sequence continues as long as the two buttons are held down.
E41 - Door open
E42 - Problems of door closure
E43 - Interlock power supply triac faulty
E44 - Door interlock sensing circuit faulty
E45 - Door interlock sensing circuit triac faulty

Possible causes:
Door interlock faulty, wiring faulty or PCB faulty.

24899241-2jugp0yd2m13ocssblsa4goy-3-0.png
Dado
0helpful
2answers
4helpful
1answer

Washing Machine does not work and shows error code E40

E40 is a door related problem. Possible causes are faulty door interlock or door circuit triac on the main PCB.
Most likely cause is the door interlock.
Not finding what you are looking for?

8,314 views

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85240 Answers

Oloyede Monsuru

Level 3 Expert

1468 Answers

Kolbrun...

Level 3 Expert

1221 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...