Question about Hampton Bay 52 In. White Redington III¿ Ceiling Fan w/ Remote Control & Light Kit

3 Answers

Hampton Bay Ceiling Fan At Slow Speed

Some one posted this problem a few months back with Hamilton Ceiling Fan. "My ceiling fan runs about 1/2 speed on high and medium and does not run at all on low. The remote LCD indicates the fan is operating in the opposite direction. The LCD indicates the fan is going forward and fan is going backward." I have the same exact problem with Hampton Bay White Redington Ceiling Fan. I tried to rewire but the fan speed stayed same while the fan ran it in differnt direction. p.s. There was an extra hot wire coming out of the celing. I also tried with that wire but same problem this time I just have to use different on/off switch on the wall. Thank you and any suggestions will be greately appreciated.

Posted by roseseller on

  • Anonymous Mar 12, 2014

    slowest speed on our 10yo "Hero" ceiling fan is now too slow

  • Anonymous Mar 28, 2014

    Can the moel 459-664 be installed on a slopped ceiling. We I operate the fan on High speed I hear TIC TIC I reduce the speed to MED & it goes away what can that be.

×

Ad

3 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I recently replaced my hampton bay fan for the same reason (slow at all speeds) and discovered scorched and melted capacitors and wiring inside the fan. My suggestion is to stop using fan and replace immediately.

Posted on May 11, 2008

Ad

auboulot

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 5 Answers

Be sure that the switch located on the fan is set to high when you are also using a wall-switch to control the speed of the fan. Avoid the mistake of having the fan-switch set to medium or low while also setting the wall-switch to medium or low. Set the fan-switch to high, then control the fan speed using only the wall control.

Posted on Sep 01, 2010

Ad

anthony james

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Is the fan single phase or three phase?in other words does the fan connect to 2 or 3 wires?if it connects to 3 wires just change 1 wire to another.

Posted on Aug 12, 2007

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fan only wobbles on high....recently 'bumped'


Check all your screws especially the set screw at top of fan that goes into rod. Blades could be warped from the water. Ball of fan not set in bracket correctly. When your buying a fan, look for blade pitch.13 degree or better is best. You shouldn't have to use the fan on high unless it's a low-end fan with a low blade pitch. It's costing you more money to run the fan on high. Sorry to get so preachy, I'm a fan dealer .

Jun 19, 2013 | Dryers

1 Answer

Hunter Ceiling fan lost medium speed, kept hi and low. Speed control capacitor melted. Replaced both capacitors (speed and start) AND switch. Still no medium speed. Is it possible part of the motor...


well, they could have. but before you throw it out, go to the hardware store, and buy a new pull switch. either that, or just run it with the high and low speeds. It shouldn't hurt it at all. But, if there is any clicking sounds, or wierd noises coming from it , DON'T USE IT!! it may catch fire. but it did last a long time. 20 years is good for a modern celing fan. though I like my antique 1907 westinghouse 72 inch 2 blade fan. It hasn't died yet!!!

Aug 12, 2010 | Hunter Ceiling Fan Control Switch

2 Answers

My hunter remote control ceiling fan doesn't go real fast. the highest speed is what a normal fan would do on medium. is there a fix?


if you have pull chain switches in addition to the remote control, your pull chain switch may be set to Medium, which would make the fan run on a maximum of medium speed.

May 16, 2010 | Hunter 52" Ceiling Fan With Light And...

3 Answers

Hunter ceiling fan-just installed -possible speed control problem


Sounds like the fan is defective. All internal wiring from the switch to the motor is factory installed. The fan has power going to it. Just to make sure, double check the wiring from the ceiling fixture to the fan.
Problem could be a faulty switch on the fan or faulty motor(bad winding for med. speed). Try reverse switch on the fan to operate the opposite direction and see if medium speed works. If medium does work in opposite direction, it pretty much points to a defective fan. In any case, unless you discover that the ceiling wires were reversed going into the fan, I'd say new fan to the returns dept.

Jul 21, 2009 | Hunter Ceiling Fan Control Switch

1 Answer

HB ceiling fan is getting slower and slower bi the day


Solid-state controls change the level of power in the fan motor to control the speed of the fan. For instance, when you switch from medium to high on a solid-state fan, the speed control mechanism increases the power of the motor. Solid-state controls are generally equipped in fans with controls that have predetermined settings, such as low, medium and high.
The solid state device in or around the fan motor could be defective and in need of replacement.
https://www.hunker.com/12003281/how-does-a-ceiling-fan-speed-control-work

Dec 07, 2017 | Hampton Bay 52 In. White Redington...

2 Answers

Wire diagram for pull chain on ceiling fan hunter original


if you indeed have a 23852 hunter original...

Black goes to L, High is Red, Gray is medium and yellow is low. Make sure you have the right switch.

Mar 21, 2009 | Hunter 23852 Classic Original Ceiling Fan

1 Answer

Casablanca fan speed problem


If this fan has a pullchain that also controls the fan speed, and you have a remote, the pullchain has to be set for the highest speed. If it is set at medium or low, it will mess with the remote operation. Note: usually high speed is the first pull after the "off" position.

Oct 27, 2008 | Casablanca Fan Bel Air 3811T Ceiling

3 Answers

Ceiling Fan only spins 1 speed


assuming you havent messed about with the wireing it can only be the pull cord switch fault or the motor is on its way out

Jul 25, 2008 | Dryers

Not finding what you are looking for?
Hampton Bay 52 In. White Redington III¿ Ceiling Fan w/ Remote Control & Light Kit Logo

5,802 views

Ask a Question

Usually answered in minutes!

Top Hampton Bay Dryers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18626 Answers

Are you a Hampton Bay Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...