Question about Hobart D300 Stand Mixer

2 Answers

Hobart D300T mixer oil change.

I have a hobart D300T mixer and it seems to have gear box oil changed since the oil in there is greasy now.
Can anybody help on what kind of oil do I need to use and how much is needed to put in?

Posted by Duke on

Ad

2 Answers

J. Hobart Tech

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 20 Answers

You can put in a all purpose grease. I use MOBIL 1 Synthetic Grease (RED IN COLOR) and it works fine -- you will need 3 tubs of 16oz's each tub. The cost is 30.00 or so. Make sure to get all of the old grease out and pack around each of the trans and worm shafts with the grease, then pack around the MOTOR GEAR and then put all back together. While running it make sure you can see the grease and hear the noise of the mixer through the 2 caps that are FILL caps on the head of the mixer. ALSO, you will find that you will lose 1st gear IF you have tigtened down too much on the LOCK nut, SOOOO loosen in small increments until all 3 gears are perfect and strong. ALSO, the key to noise adjustment is to Tighten (WHILE MIXER IS RUNNING) slowly the large nut that controls pressure on the worm transmission. The general rule with tigtening this nut is to tighten it till it will not tighten and then back off the nut -- IF the unit when starting does not run or it seems bound up when you first turn it back on, THEN you have tightened it TOO MUCH, SOOO back it off again (loosen it) until it starts smoothly and when you turn the mixer OFF it should come to a slow stop and not abruptly stop the mixer. Hope this helps some of you out there trying to do your own adjustments --

Posted on Apr 13, 2014

Ad

anthony james

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Call your local hobart branch and tell them you need grease for a d300 mixer.Yes this mixer uses grease now.If it's older they used oil but is no longer available.

Posted on Mar 16, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

D300t hobart floor mixer


best contact Hobart we have not fixed on here

Oct 09, 2017 | Food Mixers

1 Answer

My D300T motor is turning but shaft is not. How do I open the shaft area.


Weird sound usually means something in the gear box. I found a copy of the manual which includes many exploded drawings; perhaps something in here might help:
http://www.bakedeco.com/ebay/pdf/HobartD300.pdf

Nov 23, 2013 | Hobart D300 Stand Mixer

1 Answer

Hi, my Hobart D300T is making a really loud buzzing sound on start up, pls help


Could be a problem with the start windings.or start switch.maybe a capacitor .on the older models the start switch sticks just needs freed up and contacts on start switch cleaned.

Apr 15, 2011 | Hobart D300 Stand Mixer

1 Answer

What kind of oil should I use in my Hobart 800 floor mixer? [email protected]


Hello Jdnwilk,

In a Hobart L800 you use 140 weight gear oil in the head and 90 weight gear oil in the planetary. You should start with about 160 ounces and check the sight glass and fill until in the middle of the site glass after oil settles.

Thank you for choosing FixYa.com

Mar 06, 2011 | Hobart Food Mixers

1 Answer

How to remove bearings from a Hobart D300T


I have a D300 mixer and the 2nd gear kind of misses or just vibrates a little what is this?

Jan 01, 2010 | Hobart D300 Stand Mixer

2 Answers

I suspect my D300T Hobart Mixer has a broken shaft I Need a parts/manual listing to help me take apart mixer, retreive broken parts and then order required parts


Hi. Go to hobartservice.com, register for free. This will allow you access to the parts files for your D300T mixer. Download them. When you begin your disassembly, take a photo of every piece that you remove, lay these pieces on a piece of cardboard or something suitable in the order that they were removed. This will help you greatly with your project. Good luck! ricardok45

May 12, 2009 | Hobart D300 Stand Mixer

2 Answers

Hobart D300T Mixer Loud Buzzing and No Spinning


You may have a wire not fully seated in your plug, or the worm gear you've just replaced is bound by something ( a gear tooth?) or wrong worm gear. Check to see if all the gears are seated properly. You should be able to turn the agitator by hand. If not, something is jammed in the gears. The other possibility is the windings in the armature are bad.

Mar 10, 2009 | Hobart D300 Stand Mixer

3 Answers

Oil change for hobart h-600 mixer


Needed to know which part to open up to add or change oil on Hobart Mixer h-600

Mar 05, 2009 | Hobart H600 Stand Mixer

1 Answer

Hobart 140 Qt Mixer 4 speed. needs the oil changed? what kind of oil to use?


You can use a heavy weight gear oil or call the local hobart branch for it.To remove oil----Look under the mixer where the beater shaft is in the back and you will see a three quarter inch nut,remove this nut and drain the oil then put nut back in.To fill the unit remove the top cover screws and remove the top,you will see a long hexagon nut in length,remove this and grab a funnel then add the oil---be patient it takes time to fill as the oil is heavy.

Jul 24, 2008 | Hobart H600 Stand Mixer

2 Answers

Old hobart s-30 mixer oil


man you got an oldie but goodie mixer!im a hobart service tech for 8 years and have only seen about two dozen,unfortuantly parts for these units are exhuasted.as for the sight glass they do become cloudy over time and you cant determine the oil level.use a heavy gear case oil.the only way of telling is to drain the oil or if the unit is loud you should probably cange the oil.

Jan 20, 2008 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Hobart D300 Stand Mixer Logo

1,674 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1364 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Bruce Showalter

Level 2 Expert

133 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...