Jvc av56pw74 blue shadow

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
•Screen looks 3D
•Colors don't line up
•One or more colors can't be adjusted when using the convergence menu.
•Screen is bowed or warped.
•TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems






CONVERGENCE SOLUTION

You can see some more examples and find a fix using this link on Fixya - CLICK HERE

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
•Screen looks 3D
•Colors don't line up
•One or more colors can't be adjusted when using the convergence menu.
•Screen is bowed or warped.
•TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems






CONVERGENCE SOLUTION

You can see some more examples and find a fix using this link on Fixya - CLICK HERE

This tv have a problems call convergence,it dead.The tv convergence board the 2 STK convergence ICS and some or all it resistors are dead.These parts must be replaced to solved convergence problems.The shop will cost u $300-350 for parts and labors.

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projeciton sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems.






Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

CONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you are handy and can follow directions. You can get complete repair kits from TvRepairKits.com or click here. They have put together DIY repair kits that include the OEM parts and step by step photo instructions for each repair. If you are not handy or can't follow directions we would suggest calling a shop.

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projeciton sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems.






Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

CONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you are handy and can follow directions. You can get complete repair kits from TvRepairKits.com or click here. They have put together DIY repair kits that include the OEM parts and step by step photo instructions for each repair. If you are not handy or can't follow directions we would suggest calling a shop.

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony, Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit from the link below.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on - TV may also make a chirping noise.

Here are some photos of convergence problems.





Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a solution

CONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you know what you are doing. If you have never done this before we would advise calling a shop or if you want to do it yourself get a complete kit with instructions and support from www.TvRepairKits.com

Remove front grill and chip board ,there are three knobs one is for brightness I think another for a sharper picture (best to use while convergance adjustment and the third which should balance your
black or white screen to have blue,red, or green tinge ,you like to have it as neutraul as possable.
if you are stll getting everything in blue,green or b-52 agua marine ,your red lamp may be burnt out!.

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems.






Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

CONVERGENCE SOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projeciton sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems.






Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

CONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you are handy and can follow directions. You can get complete repair kits from TvRepairKits.com or click here. They have put together DIY repair kits that include the OEM parts and step by step photo instructions for each repair. If you are not handy or can't follow directions we would suggest calling a shop.

my suggestion would be...to replace the focus block..john