I have a WRT300N ver 1.0, before it was ver 0.9 but I install firmware for 1.0. after update router doesn't work. I run ipconfig on pc ant it looks everything fine but I can't connect to the internet. I would like to return to a older version....it is possible....??? TNX in advance

Solution 1.

How can I reset the Linksys WRT300N to factory defaults?
Hold the Reset button on the Linksys WRT300N for about 30 seconds.

What is the IP Address, Username and Password to log in to the WRT300N?
IP Address: 192.168.1.1
Username: none
Password: admin

You should also know the configuration of your ISP provider after reset. You'll need to re configure your connection from modem to router.

Solution 2

How do I upgrade the Firmware on the Linksys WRT300N?
# 192.168.1.1 -> Administration tab -> Firmware Upgrade sub-tab. Click "Browse" and browse to the firmware upgrade file on your computer. Click "Start to Upgrade". Do not reset or power cycle unit while it is upgrading.


What is the IP Address, Username and Password to log in to the WRT300N?
IP Address: 192.168.1.1
Username: none
Password: admin

it looks like firmware fault try to update the firmware to see if that helps

You have WRT300N router. If it is very old model then upgrade the firmware of the router. and try changing the wireless channel on the router.
Firmware is the software of the router.
Download the latest firmware of the router. Go to the manufacturer's web site and download the firmware of the router.
Open the set up page of the router and upgrade the firmware of the router. Once you upgrade the firmware of the router, reset the router.
On the router you will find a small reset button, hold it down for 30 seconds. release it. wait for 1 minute. Now unplug the power to the router and plug it back in.
Now you will need to reconfigure the router according to the Internet service provider.

You are going to have to find a software that helps you force reinstall the Firmware. Something went wrong somewhere, I know the software exists, i used it to install a 3rd Party Firmware on my linksys to gain Access Point Functionality

WRT300N router has issues with firmware. Upgrade the firmware of the router.
Download the new firmware from the web site www.linksys.com/download . save it on your computer. open the set up page of the router.
Upgrade the firmware of the router. Once you upgrade the firmware , reset the router for 30 seconds. Release the reset after 30 seconds. wait for 1 minute. unplug the power and plug it back in. wait for 1 minute.
Now you will need to reconfigure the router.

Click here for more information

hi

first of all you need to remove dlink from the network

once you do that attach linksys and in your laptop type cmd in run box and then click ok once you do that it will give you a command promt then in command prompt type ipconfig and hot enter,,once you do this it will give you a ipaddress and default gate way for the linksys and then go to internet explorer or any browser and type the default gate way number on the address bar ,,once you do that it will open up the router page for linksys and you can do the desire setting change on the router ,,,,,,,if not you can contact me on fixya

Apparently not, but I'm guessing you already knew that.
http://www.linksysbycisco.com/US/en/support/WRT54G/download

Look carefully at the label and the firmware installed in your router. The 1.02.5 is listed for 5 and 6 only and version 8 is for 8 only. There is no 7 listed, so it was either a special run or there is just no firmware upgrade for it yet. It must have been perfect :-)

Carl

The 2 different operating systems can run off the same router. Also check to see which type of security you are using I would suggest WPA2 if you do not see that listed you will need a firmware update.

MP3 XINTAI Firmware. Please pass it to the other repliers at the forum, or anyone who needs it.

Hi pals.

At last!, I've backed-up the firmware for Xintai MP3 Player from Wilson Co. Ltd., and put it here:

http://www.paginasprodigy.com.mx/darkwing/Xintai9152_Wilson.zip

Don't worry cause one of the files (at UI30.RES) has an incorrect checksum. It's due to prior edit on ASCII labels.

I couldn't say it is really the firmware you want, so you must check and verify thoroughly before proceed.

Please note:
1.- Do not update or reload firmware if your player is working fine (more or less).
2.- If this firmware is not EXACTLY the same version, for the same chipset, there's no guarantee. The player could not work or, even worst, could suffer defintive damage.
3.- It's highly recommendable you BACKUP the existent firmware, despite damage suspects.
4.- To backup and/or restore firmware for this player, you can use "S1res" Ver 4.1, downloadable at:

http://www.s1mp3.de/tools.s1res.html

For restoring firmware, you can also use the "Player Upgrade Tool" Ver 4.18 or superior (part of "MP3 Player Utilities"), downloadable at:

http://www.mympxplayer.org

Enjoy your music.

---------------------------------------------

XINTAI MP3 Player
Wilson Co. Ltd.
Bootflash type: F285
brom version: 3.0.80
Firmware version: 9.1.52
Date: 9-01-05

VID: 10D6
PID: 1101

V9-device
giveio ver: 3.0
Flash chip: A514D3AD "HYNIX/SAMSUNG 1024 (LBF)

MTP Manufacturer: Auctions Semiconductor Co.
MTP Version: V1.00.3333
MTP VID: 10D6
MTP PID: 2200

----------------------------------------------

Hi Beluis,

Go to Start>Run, type in CMD. In the black box that opens, type in IPCONFIG /ALL. Look at your IP, Gateway, and DNS settings.
IP should be 192.168.1.xxx, Gateway IIP should be 192.168.1.1
DNS should have numbers, but they may vary. If they are not in those parameters, you won't be able to access the router. Let us know if these are right.
The router wiill give you an IP, and Gateway, with no DNS, and that will stop your from accessing the internet.
Shut down that modem, router, and your PC, Make sure your ethernet cable goes from your modem to the WAN, (not LAN!) port. Power up the modem, wait a full 2 min, power up the router, wait a full 2 min, and start up your PC. Try the IPCONFIG again.

Good Luck.