Mod ps2 slim scph 77006

Modding is the process of putting a mod chip in the ps2 to read burned games and to hack games. I wouldn't recomend doing it because it is highly illegal.

Depending on what modchip you used, sometimes DVD Playback can be lost, you need to ensure that your modchip supports DVD playback but there is a way around this, now that you have a modded system you can run arbitrary code and .elfs, just google "Free MCBoot for ps2 slim", after its setup download the media player for ps2 burnt it on a cd rom or put it on a pendrive and run it, Hope this helps...

the disk itself might be corrupted

You cannot connect a usb hardrive or anything for that matter unless you "soft mod" the ps2 you need a pro action repaly and the usb stick that comes with it and you need to put certain installtion files on the stick with your computer.

Google: "Mod slim ps2 to play backups"

There were two versions of the multi-tap made; one for the original fat PS2 and a smaller version made for the slim. The two versions are incompatible with the other PS2. If you have the original multi-tap connected to the slim, it should throw out the 'controller disconnected' message when you boot up. The slim version of the multi-tap should have a sticker on the bottom saying 'only works with models SCPH-70000, SCPH-75001, SCPH-75002'.

Other than the sports games, I don't recall any titles that allow more than two players anyway.

Your DVD potentiometer pot on the back of the PS2 laser lens needs to be readjusted. Some people will try to tell you it's out of alignment but if that was the case it would not read CD's. Some people will try to tell you the laser lens is bad. If that was the case it would not read CD's. On the back of the laser lens are two potentiometer pots. In english? Two lil screws that are turnable. One controls the power of the DVD laser one controls the power of the CD laser.

http://www.cyber-mag.com/station/laserV9.htm

That link will give you pretty lil pictures of what i'm talking about :)

In a nut shell the story goes like this folks. If your PS2 won't read certain game DVD's that are of a certain color or if it all of a sudden mysteriously fails to read games it once read but will play cd's just fine, the voltage of the laser for DVD's is not set correctly. (this does needs manual tweeking from time to time if you take your ps2 and move it around alot or if you take it over to friends houses etc etc. Basicly alot of movment in general can take this out of alignment. Even keeping the PS2 on it's side could theoreticly (just my opinion) based on gravitational pull, unbalance the potentiometer.

RESOLUTION:

Step 1 identify your PS2 version:

Version 1 - SCPH-30001, 10 screws on bottom of case, serial no. starts with "U1"
Version 2 - SCPH-30001, 10 screws on bottom of case, serial no. starts with "U0"
Version 3 - SCPH-30001, 10 screws on bottom of case, serial no. starts with "U2"
Version 4 - SCPH-30000, 30001, 35001, 30002, 35002, 30003, 35003, 30004, or 35004, 8 screws on bottom of case

NOTE: Version 4 has 2 varieties of motherboard: Gap/No Gap, the difference between v4 "Gap" and v4 "No Gap" is the "Gap" is there's a spot in the center of bios chip where each side lacks solder points.

Version 5 - SCPH-30000R, 30001R, 30002R, 30003R, 30004R, or 30006R. Also, some SCPH-30000, 30001, 30002, 30003, and 30004 models have a V5/V6

NOTE: Version 5 & 6 - the difference between these two versions is one of the connectors in the corner.

Version 7 - SCPH-39000, 39001, 39002, 39003, 39004, 39008 or 37000
Version 8 - Only in Japanese consoles. SCPH-39000, or, SCPH-39006 (GH-022 BIOS 090)
Version 9 - if you have SCPH-50000, 50001, 50002, 50003, 50004, 50006, or 50007 you have a v9 or v10 board.
Version 10 - SCPH-5000x, with date code "3D" to the right and below the serial number on the back of the console. (GH-026 board)

NOTE: To know if its a v9/v10 start up PS2 with no game in it ,press triangle and check dvd driver version dvd ver 3.00 = v9 & dvd ver 3.02 = v10.

If your model # is SCPH-50000, 50001, 50002, 50003 or 50004 AND if you can find a small ''a'' under the SCPH number or have DATECODE "3C" you have a V9 PS2 main board. (GH-026 board).

If your model # is SCPH-50000, 50001, 50002, 50003 or 50004 AND if you can find DATE CODE "3D" as shown below, you have a V10 PS2 main board. (GH-026 board).

Version 12 - The new slimline PS2 consoles are referred to as PSTwo here, but elsewhere they are also known as "v12" units... their numbers are SCPH-70011/SCPH-70012, and also SCPH-70004 CB (Belgium).

Step 2 use either google or the link above. If you're using google your keyword search will be something like "ps2 v12 laser lens adjustment" *replace v12 with your ps2 model.

In either case navigate to the site and follow instructions to set the pots back to their factory default settings.

The Modbo v4.0 is compatible with v5 to v16 and it is also compatible with the newly released SCPH-7700x & 7900x consoles. However for your SCPH-30004 I'd use a PS2 Duo 3 Gold. http://www.duomodchip.com/english/install.htm

I don't really think I can find any info. on that. I would suggest calling or visiting the person/company that installed the mod-chip. I wouldn't call sony playstation because downloading games for the ps2 can sometimes be illegal.

hello pauldonp...if this is an early version of the slimline they had a problem with over voltage which inturn took out the laser.your only option may be to replace the laser . sony did bring out a mod for this..i preferr the real old version of the ps2 as they had all separate boards and if one went faulty you didnot have to replace the lot ,also the lasers were a lot cheaper than the later models .in the slim lines the lasers are not all that expensive .they do take a bit of setting up as you have to know the ohms setting on the laser for each model..hope this helps

Try to move the laser forward-back, if you have the unit open it's a good idea to perform some routine cleaning, preferably using a can of air, and check for areas such as the worm drive, and guide arms that may need re-greasing, as these parts can affect the operation of the console if they are dry. if it not work, there is two switch are used to runing laser. 1-eject switch ,2-loading switch. see on pictuce below.


Sometimes that switch has bad connection, you may need to spray it with contact clean, then press it manually. You can call SONY support at 1-800-345-7669 for repairing.

Pls post back should you need additional information. Hopefully this helps.