Question about Labtec Optical PS2 911544-0914 Mouse

1 Answer

Labtec optical mouse

Cant remember how to set up, I threw the manual away, I seem to remember you cant switch on the mouse until the device has started?? any ideas from start to finish?

Posted by James Connolly on

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 317 Answers

Is this a wireless mouse? If so, plug the USB connector into your computer. The pc should detect it and install the drivers automatically. Then there should be a button on the bottom of the mouse, press it, then press the button on the USB connector. This establishes a connection between the mouse and connector.

Posted on Aug 07, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dont have the handbook as my son threw it away now cant set radio stations cant set anything without the book


Try this link and click on one of 3 manuals listed for PDF download.

http://books.jvc.com/booklist.asp?Model=KD-R616

Feb 06, 2011 | Car Audio & Video

1 Answer

Cant find directions but cant seem to remember how to establish link between mouse and remote


Press the connect button on the remote sensor and when it blinks press the connect button under the logitech mouse. The blinking on the receiver should stop if it finds it. Make sure there are not wireless devices like cordless phones, etc beside the receiver or mouse as it degrades the signal.

Jan 15, 2011 | Logitech Cordless Mouse

1 Answer

Hey i threw away the instructions on my bluetooth by accident and now i cant register it because i don't have the passkey. what's the passkey?


Usually you may set the passkey yourself from the device you're syncing your bluetooth with, however, this may vary by brand or model.

If you try to sync and create your own passkey and it doesn't work you should be able to find an online instruction manual for your unit by visiting the manufacturers website. I hope this helps.

Oct 16, 2010 | Cell Phones

1 Answer

Optical light on Mouse not working


Hello,

maybe the battery?
follow the steps below to troubleshoot the mouse
Wireless mouse does not respond (generic instructions)

Try to Resynchronize your device with the receiver(connector)
Follow these steps.:
Note When you synchronize the mouse or the keyboard with the receiver, put the device near the receiver and put other wireless keyboards and mouse at least 6 feet away.
1. Press the button on the receiver, and then verify that the light on the receiver starts to blink.
2. If a dialog box appears on the screen in several seconds, follow the instructions that appear on the screen. Otherwise, go to the next step.
2. Press and release the Connect Channel button on the bottom of the mouse or the keyboard.
3. Check the green light on the receiver. A steady green light means the synchronization was successful. If the problem persists, try steps 1 through 3 again.
For the Wireless Notebook mouse: This issue can occur if the micro-switch on the bottom of the mouse is not released. Use a pin or a pen to try to release the button if it is depressed.
or
Try different port and restart your computer.
or
Reinsert the batteries or install fresh batteries
If you have the possibility check whether the problem is because of your computer or the device, try the mouse or the keyboard on a different computer.

Sep 06, 2009 | Microsoft Wireless Notebook Optical Mouse...

4 Answers

Same prolem with a m8s dell dimension 3100


Every Device connected would lit up while you start the computer,power on self test.Set the BIOS to Default.

Jul 06, 2009 | Dell Dimension 3100 PC Desktop

3 Answers

I threw away my instructions on my Contour Design BlueTek


Here are the instructions from the manual for my Contour Design SURFACE SOUND COMPACT (with minor editorials)

To initiate pairing:
  1. Place the bluetooth device and your mobile phone within 0.3 meter (1 foot) of each other - I prefer to place both on a table infront of me
  2. Switch on your phone and select it Bluetooth discover mode (you'll have to figure this one out on your own!)
  3. Immediately after turning the bluetooth device on (ie. lifting the microphone), press and hold both the TALK button and the VOL + button for about 5 seconds until the indicator light flashes red and blue alternately and a sound can be heard in the speaker - I had trouble getting it to co-operate once it started into the seeking handset mode of beeping, so try to press the two buttons before all that beeping starts
  4. Once the mobile phone detects the carkit, a "contour SSC" message will be displayed. Follow the phone instructions to accept the pairing. The PIN coade (or passkey) is 0000, then press "yes" or "ok". I assume the PIN code is the same for all of them, as the manual appears mass printed.
If the pairing was successful, the indicator light will switch to blue and flash slowly. If you haven't started the discovery mode within 5 minutes, it will stop. In this case, you must start the pairing again as step 3 above.

Jun 22, 2009 | Contour Design 00903-0 SurfaceSound...

1 Answer

Recorded message plays in Spanish. Husband threw the manual away.


Way too easy :-)

When you were listening to messages you probably pressed the SKIP button for longer than 2 seconds. Try pressing it and holding it again and see what happens.

Here's the manual link: http://www.home-electronics.net/ge/pc/IB/25942GE3_IB.pdf

Carl

Mar 13, 2009 | General Electric 25942EE4 Quad Cordless...

1 Answer

Keyboard wont work for bios !!


What you have is a Usb Keyboard, The most of usb boards don't starting to work after you got to the login screen.. Get a Old keyboard thats not usb and it will work


Remember to rate

Jan 11, 2009 | Computers & Internet

1 Answer

Microsoft Wireless Laser Desktop 4000 Problem (USB UNRECOGNIZED)


install a logitech driver for this mouse they usually have a compatibility issue with an irq in nividia but with logitech drivers the irq setting is set off the nividia set

or you can manually set the irq setting for either nividia or your mouse manually did the techs explain this too you when you took it in
this is likely the case that the wireless l.d. is haveing conflict with nividia irq setting

heres a link with another possiblility that is states its 2 links one for all the troubleshooting problems and the one decriscribed of what your asking about

http://support.microsoft.com/default.aspx/ph/9961?cid=C_53569
trouble shooting page with all problems if you want to look threw every one on the page

http://support.microsoft.com/kb/223256/en-us
the actual problem page so you dont have to go looking for it yourself threw all the links posted on first link

Jun 13, 2008 | Microsoft Wireless Laser Desktop 4000...

Not finding what you are looking for?
Labtec Optical PS2 911544-0914 Mouse Logo

376 views

Ask a Question

Usually answered in minutes!

Top Labtec Computers & Internet Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Resolution IT Dubai
Resolution IT Dubai

Level 3 Expert

541 Answers

Rob Hill
Rob Hill

Level 3 Expert

1426 Answers

Are you a Labtec Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...