Attention and ready light on - HP LaserJet P2015 Printer

If your HP Printer blinking lights that meand printer has some technical or mechanical errors. The HP printer has blinked different lights and that has different meaning and solutions. You can find here why your HP printer blink ready light. Read the causes and solutions to fix the HP printer lights blinking.

contact your service provide for assistance on how to set it up

Here is a full story

HP LaserJet Professional M1130/M1210 MFP - Interpret control-panel light patterns (M1130 Series only) Interpret control-panel light patterns (M1130 Series only) If the product requires attention, an error code appears on the control-panel display. Status-light legend Symbol for "light off" Symbol for "light on" Symbol for "light blinking" Control-panel light patterns Light status Error code State of the product Action All lights are off.

The product is turned off. Press the power button to turn on the product. Ready and attention lights blink.

The status lights cycle during the formatter initialization period or when the product is processing a cleaning page. No action is required. Wait for the initialization period to end. The product should enter the ready state when the initialization period is finished. Ready light is on.

The product is in the ready state. No action is required. The product is ready to receive a print job. Ready light is blinking.

The product is receiving or processing data. No action is required. The product is receiving or processing a print job. Ready light is blinking slowly.

The product is in low power mode. No action is required. Attention light is blinking.

E0 Paper is jammed in the product. Clear the jam. E1 The input tray is empty. Load the tray. E2 A door is open Verify that the print-cartridge door is fully closed. E4 The product memory is full The job is too complex for the product to print. Simplify the job, or divide it into multiple files. E5 The product did not pick up paper from the tray. You might need to clean or replace the pickup roller. H0 The product is in manual-feed mode. Load the correct paper type and size into the input tray. H1 The product is processing a manual duplex job. Load the pages into the input tray to print the second sides. The attention and toner lights are blinking.

E3 The print cartridge is missing or is not installed correctly. Install the print cartridge. The toner light is on.

The print cartridge has reached the end of its estimated useful life. When the supply has reached this condition, the HP Premium Protection warranty for that supply has ended. You do not need to replace the print cartridge at this time unless print quality is no longer acceptable. Attention light is blinking, and ready light is on.

The product has experienced a continual error from which it will recover on its own. If the recovery is successful, the product continues to the processing data state and completes the job.

If the recovery is unsuccessful, the product continues to the continuable error state. Try removing any media from the media path and turning the product power off, and then on again. The attention and ready lights are on.

E6

E7

E8

E9 The product has experienced a fatal error from which it cannot recover.

1. Turn off the product or disconnect the power cord from the product.
2. Wait 30 seconds, and then turn on the product or reconnect the power cord to the product.
3. Wait for the product to initialize.

If the error persists, contact HP customer support

ATTENTION light(triangle): Indicates that the print-cartridge door is open, print cartridge is missing, and other errors.

If ATTENTION and READY light is blinking:

Printer initialization
The printer is initializing.
No action is necessary.

Cleaning mode
A cleaning page is printing.
Wait until the cleaning page has finished and the printer is in the Ready state.
This could take up to two minutes.

If ATTENTION and READY light is on:

Fatal error
Turn off the printer, and then unplug the printer power cord for 30 minutes.
Plug the printer power cord into the power outlet, and then turn the printer on.
If the error persists, replace the printer.

If ATTENTION light is blinking and READY light is off:

1. Attention: door open, no print cartridge, or media jam
   

The printer is in an error state that requires operator intervention.
Check the following:
? The print cartridge door must be completely closed.
? The print cartridge is correctly installed.
? There is no media jam.

2. Out of memoryThe printer is out of memory.
The page you are printing might be too complex for the printer's memory capacity.
Try lowering the resolution.

Error description:

The Attention (red) light is blinking. There are six possible causes that will display the Attention light pattern:

-Paper out
-Door open
-Print cartridge missing
-Paper jam
-Paper sensor jammed
-Duplexer error

Solution :
After the cause of the problem has been addressed, pressing GO will cause the printer to attempt to recover from the cause of the error. If the printer is unsuccessful, it will continue to display the Attention message until the cause is remedied.

Pressing JOB CANCEL will cancel the print job and the printer will return to the Ready state (Ready light on) unless there is a paper jam still in the printer or the print cartridge is not in the printer.

For more details visit the link below :

Resolve Printer issue

According to your "secondary" light pattern your printer has a Carousel motor error.
You've already power cycled it to no avail.
The next step is to get the motor replaced.

Sorry, I know that you didn't want to hear that.

takes several minutes to come up and ready

Any message displayed?
Does it beep?
Have you done the obvious, check paper, look for paper jam, toner supply?

Hello,

Please perform the following.

Super NVRAM initialization Turn off the printer.

1. Press and hold the Go button.
   
2. Turn on the printer and continue to hold the Go button for at least 50 seconds. During this process, the Attention , Ready , Go lights turn on. Then the Attention and Ready lights turn off, leaving only the Go light illuminated.
   
3. Release the Go button. The Go , Ready and Attention lights turn on.
   
4. Press and hold the Go button. All lights turn off. During the next three seconds, the Go , Ready and Attention lights turn on in that order, one per second.
   
5. Release the Go button to perform the initialization. The control panel lights begin cycling from front to back. After the Super NVRAM initialization process is complete, the printer returns to the ready state.
   

Hello,

Please perform the following:

Unplug the network Cable:

Cold reset A cold reset changes most system parameters in NVRAM to the factory defaults. However, unlike NVRAM initialization, a cold reset does not reset the page count, the paper tray sizes, language, or formatter number.
A cold reset also resets all the HP Jetdirect settings as well as the printer settings. Use the following procedure to perform a cold reset.

1. Turn off the printer.
   
2. Press and hold the Go button.
   
3. Turn the printer on, and continue to hold the Go button for at least 5 seconds, but not longer than 15 seconds. During this process, the Attention LED turns on.
   
4. Release the Go button.
   If both the Attention and the Ready LEDs turn on before you release the Go button, you must start the procedure again with step 1.

The printer's LEDs begin cycling. The cold-reset process runs until completion, and the printer returns to the ready state.


Network reset A network reset changes all network system parameters in NVRAM to the factory defaults. During the network-reset process, all button presses are ignored.
Use the following procedure to perform a network reset.

1. Turn off the printer.
   
2. Simultaneously Press and hold the Go and Job Cancel buttons.
   
3. Turn on the printer and continue to hold the Go and Job Cancel buttons for approximately 10 seconds, but no longer than 20 seconds. During this process, the Attention light turns on.
   
4. Release the Go and Job Cancel buttons. The Attention , Ready , and Go lights begin cycling from front to back. After the network-reset process is complete, the device returns to the ready state.
   If the Attention and Ready lights illuminate before you release the Job Cancel button, start again at step 1.

Now plug in the network cable and then wait for 5 mins.
Then print a configuration page and check the IP Address.