How does the bobbin case go in the machine - Singer CE-200 Quantum Futura Computerized Sewing Machine

If your Singer model 600e's bobbin case is stuck, try the following steps to remove it:

1. Turn off the sewing machine and unplug it from the power source.
2. Raise the presser foot and the needle to the highest position.
3. Open the bobbin cover and remove the bobbin from the bobbin case.
4. Locate the lever or button that releases the bobbin case from the hook race. Depending on the model of your Singer sewing machine, this may be a lever, a button, or a latch.
5. Use your finger or a small screwdriver to press or move the lever, button, or latch to release the bobbin case from the hook race.
6. Gently pull the bobbin case out of the machine.

If the bobbin case is still stuck, do not force it. Instead, seek assistance from a trained sewing machine technician or contact Singer customer support for further advice.

If your bobbin and bobbin case are stuck on your 880 Bernina sewing machine, there could be several potential causes for this issue. Here are some possible solutions to unstick the bobbin and bobbin case:

1. Check for any debris or lint that may be blocking the bobbin and bobbin case. You can try using a small brush or toothpick to remove any debris or lint that may be blocking the movement of the bobbin and bobbin case.
2. Check the tension on the bobbin case. The tension on the bobbin case should be adjusted to match the type and weight of the thread you are using. If the tension is too tight, it may be preventing the bobbin and bobbin case from moving freely. You can try adjusting the tension on the bobbin case using the tension dial or screw on the case.
3. Check the position of the bobbin case. The bobbin case should be positioned correctly in the sewing machine to allow the bobbin and bobbin case to move freely. If the bobbin case is not properly positioned, it may be preventing the bobbin and bobbin case from moving. You can try repositioning the bobbin case in the sewing machine according to the instructions in the sewing machine manual.
4. Check the condition of the bobbin and bobbin case. If the bobbin and bobbin case are old or damaged, they may be stuck or difficult to move. You can try replacing the bobbin and bobbin case with new ones to see if this fixes the problem.

If none of these solutions work, it may be necessary to disassemble the sewing machine and clean or repair the internal parts that are preventing the bobbin and bobbin case from moving freely. This is a complex task that should only be performed by a qualified sewing machine repair technician.

Sure, I can help you with your Bernina 800 bobbin case problems. What sort of issues are you having?

Most bobbin cases have a latch that must be released to remove or install in the machine. Be sure to hold the latch open while you insert the bobbin case into the machine. Rotate the bobbin case slightly until it feels seated. Then release the latch. If the bobbin case is not latched in place, it will continue to fall out whenever you begin to sew.

try changing the needle
rethread the machine top and bobbin
make sure the bobbin is inserted correctly into the bobbin case
and that the bobbin case is inserted correctly in the machine
it's also possible that the bobbin case needs to be replaced
also check the bobbin it could be warped
it's also possible that the timing needs to be checked on the
machine

is this a top or front or side loading bobbin case?

Hello

Make sure your feeddogs are up. That is the little jagged looking plate under the pressure foot. There should be a setting on your machine that will move it up and down.

If they are up then the bobbin is not in correctly. If it is a normal round bobbin that fits in a bobbin case, hold the bobbin in front of you so that the thread end is on top and the thread is going away from you, and slide it into the bobbin case. Feed the thread through the right openings in the bobbin case. When you pull the thread end the bobbin should turn clockwise.

Never hand-wind bobbins. Instead, use the accompanying bobbin winder which is attached to most machines,bobbin casings must be oiled regularly to prevent problems with the bobbin turning properly. The bobbin, when inserted properly into the bobbin casing, should spin counter-clockwise when thread is pulled.

Check the way your machine is threaded. Completely un-thread your sewing machine and re-thread it. Remember to always thread your machine with the presser foot up.

Check the bobbin and be sure the bobbin is threaded correctly and that the bobbin case is correctly threaded. Be sure the bobbin is in the bobbin case in the correct direction.

Always watch for bobbin wear, especially on the plastic type of bobbins. If the edges of the plastic are showing abrasions, the size of the bobbin has changed and may be the culprit. Although the size change is minute, it allows the bobbin to wobble in the case and changes the tension.

Inserting bobbin into the bobbin case or problem inserting bobbin case into the shuttle?

Make sure the thread will feed from the bobbin clockwise and through the guide on the bobbin case.

Lift the lever on the bobbin case to hold the bobbin in place as you inset the bobbin case into the shuttle.

If the bobbin case for this machine as a "finger", this has to align with the opening in the shuttle.

If you cannot readily see this - move the bobbin case a bit to the left and right until it clicks into place.

Viking bobbin case tension adjustment:
When the bobbin runs out, sometimes it bends the bobbin case tension spring. Then tension is too light. Take the bobbin case out of the machine. Tie the loose bobbin thread to the Designer 1 needle plate. Insert the bobbin in the bobbin case. Here’s the tricky part set the bobbin case on the table as if it’s in the machine (Bobbin is visible and sitting horizontal to table top) threaded as if sewing and loose end tied to needle plate (that is removed from the machine). Lift the bobbin case off the table rotate it so that the flat side of the bobbin are vertical to the table and no longer horizontal. Have the bobbin case oriented so that the thread coming out of the bobbin case sprint (slot area where it is put for sewing) is at the top. Lift it high enough that the needle plate is lifted from the table. It should not release thread unless you shake it gently and then a very small amount of thread. The needle plate is the exact weight resistance your bobbin case should have on the thread.