Question about Kenmore 24 in. 16182 / 16189 Built-in Dishwasher

1 Answer

Kenmore dishwasher how to remove door of main soap dispencer to r

Spring broken.how do you remove the lid to replace the spring?

Posted by jr_plater on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 70 Answers

First you need to find out if it really is a spring or is it a rope system. Remove the lower panel and look to the left or right and see if you have a "spring" or is it a "rope". IF you have a rope, you will need to slide the dishwasher out so you can get to the back of whichever side it is broken on and make the loops required.
Good Luck!

Posted on Feb 26, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Printer message cover open


There is no replacement part available from Dell. Temporary fix is removing the hinge spring under the small concave white plastic piece (you can remove that also) allows the cover to close. The nub under the cover has to press a "lid closed" switch which is not possible if the lid hinge is broken.

See this link:
http://www.fixyourownprinter.com/forums/inkjet/66032

Jul 27, 2011 | Dell 948 All-In-One InkJet Printer

2 Answers

15 yr old admiral 20 lb. (I think it is model 35-4119 ) walks


You gonna have to remove the front and look for a broken spring, If the springs are all there then the snubber pad probably needs replacing.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Mar 05, 2010 | Washing Machines

1 Answer

NEC nw 452 The spring on the lid cut-off lever has broken. I need to remove the lid. How do I do that?


You need to open the top. Unplug the machine and find a stiff putty knife or something flat and thin. Where the top meets the front of the machine, about 2" in from both sides, you will find a spot where you can push inward and release the spring catches. Lift the top and everything will be accessable.

Nov 05, 2009 | Washing Machines

1 Answer

Replace broken door springs F&P dw918td


To replace the door springs, you need to remove both the side covers. This can be done by first removing the lid and then working your way around both panels until they come off. You will then see on either side a cord that is attached to a single spring.routed on a small bend. Very unlikely the spring is broken but possibly the cord has or it has pulled loose from its position. Rectify then reassemble.

Sep 27, 2009 | Dishwashers

1 Answer

Washer makes banging sound as it washes.IS NOT OUT OF BALANCE AND NO CODES ARE SHOWN .IS IT POSSIBLE DRUM IS LOOSE


Could be a suspetion fault, a broken top spring or lower shock absorber gone faulty. Tip the machine back and check the shocks aren't breaking up, also take the lid off and check the top springs are good(usually 2 screws at back of lid, lift and pull back to remove)

Jul 02, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Washing m/c spinner lid to be replaced- Position of the spring


I would seek out the local washing machine engineer for a quote as it may need to be replaced by an expert eric

Jan 15, 2018 | LG Washing Machines

2 Answers

How to replace hinge lid pins


At the back of the washer just below the control panel there are two 8mm metal screws remove them there are 2 clips they will alow you to lift the top up in the front of the washer the top cover has 2 spring type holders if you slide a small screw driver in the opening and push gentle on the spring clips they will release and you can lift the top off the washer there is a screw on each hinge this will remove the old hinge then replace with new ones hope this will help

Jan 24, 2009 | Maytag PAV2300 Top Load Washer

3 Answers

Jetta 2003, trunk won't lock


More than likely the spring inside the latch has come undone. To save some money you can remove the latch from the trunk, open the latch and reset the spring. To Remove the latch you will need to remove the carpeted cover on the trunk lid (there are about 10-15 phillips screws holding it on.) Once the cover is off disconnect the rod going to the latch by opening up the clip thats connected to the actuator. Disconnect the wire harness, Remove the 2 10mm Nuts holding the latch to the lid. Remove the black plastic cover on the latch and remove the electrical piece (the plastic cover wraps over the latch and is secured buy 2 plastic pressure snaps). Look down into the latch and you should see a small spring...on my Jetta the spring wasn't connected. take a small pointed object ( I used a light tester) and reattch the spring to the black hook. Mine had some broken plastic in it and After I removed that it worked fine. Once the spring is back into place reassemble the trunk and you should be good to go. No money spent, and it only takes about a half hour or 45 mins to do.

Dec 01, 2008 | 2003 Volkswagen Jetta TDI

1 Answer

Whirlpool lsb6200kq0


Remove the two screws in the top of the console they will be in the rear left and right side or in the front corners
then flip up the console and remove the 2 spring clips (brass)and the lid switch molex plug the cabniet will come off tilt forward and pull out you will see the lid switch running on the underside

Mar 04, 2008 | Washing Machines

Not finding what you are looking for?
Kenmore 24 in. 16182 / 16189 Built-in Dishwasher Logo

Related Topics:

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Ron Rak
Ron Rak

Level 2 Expert

138 Answers

Cindy Wells

Level 3 Expert

6099 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...