Wireless controller control functions does not work.

Connect a game controller
Solutions
Learn how to connect a wireless or wired controller to your Xbox 360 console.
Connect a wireless Xbox controller

1. Turn on your console.
2. Press and hold the Guide button on the controller until the controller turns on.

1. Press and release the connect button on the console.

Xbox 360 E console Xbox 360 S console Original Xbox 360 console

1. Within 20 seconds, press and release the connect button on the controller.

1. When the lights surrounding the power button on the console stop flashing, the controller is connected.

On the Xbox 360 S console, each connected controller is assigned to one of four positions. Each position corresponds to a lighted section around the console power button and the controller Guide button. On the 360 E console, a solid green light on the front of the console indicates that the controller is connected. To determine the player position associated with your accessory, look at the ring of light that surrounds the Guide button on the controller.

If the controller does not turn on, check the batteries. Insert fresh AA batteries, making sure they are correctly positioned in the battery case.
You can also use the Xbox 360 Play & Charge Kit or the Xbox 360 Quick Charge Kit to power the controller. Learn more about Xbox controllers and chargers.
To connect additional controllers, follow these same steps again. You can connect up to four controllers to the console. Each connected controller is assigned a position that corresponds with the lighted sections that appear around the console's power button and around the Guide button located in the middle of each controller.

• To disconnect a wireless controller, press and hold the Guide button for three seconds, and then choose to turn the controller off.
• When you turn off the console, the controller will reconnect the next time you turn on the console.
• The controller can be connected to only one console at a time. You can connect the controller to a different console, but the connection to the previously connected console will be lost.

1 Disconnect all accessories and wired controllers from the Xbox 360.
2 Hold the "Guide" button down for three seconds on any wireless controllers, then respond to the prompt on your television screen to disconnect the controllers from your system.3 turn on the wireless headset by pressing the "Power" button in the center of the earpiece. 4 Press the "Connect" button on the front of your Xbox 360 system. 5 Press the "Connect" button on the wireless headset. The ring of lights around the power button of the Xbox 360 system should spin and blink once. One of the lights should remain lit up, indicating the port number that the headset is using. If you do not see any lights on the system, you may have a faulty wireless headset.6 Press the "Guide" button on your wireless controller to reconnect the controller to the Xbox 360 system. If you are using a wired controller, you can plug it back into the system.7 Press the "Connect" button on the top of your wireless controller to sync the controller with your system. You should see the connection light around the "Guide" button on the controller light up, indicating which port you are connected to. You should also see a corresponding port light in the ring around the power button of your Xbox 360 system 8 Press the "Connect" button on the wireless headset until the port light on the headset matches the light on the controller and Xbox 360 system. For example, if you are the first player, the light for port number one should be lit up on the Xbox system, the controller and the headset. When all lights correspond, your headset should be properly connected.

How to Configure an Xbox Controller Fotolia.com"> Configure you Xbox controller.

The Xbox 360 utilizes two types of controllers: wired and wireless. Like most operations on a video game console, configuring a controller requires little effort. You can either plug the controller into a port on the Xbox 360, or sync a wireless controller using the console's built-in controls.
Difficulty:Easy Instructions

1. Wired
   • 1 Connect the controller's cable to the in-line release cord. This cord prevents you from accidentally pulling the Xbox 360 along with your controller during game play.
     
   • 2 Insert the in-line release cord's USB plug into the USB port on the front of the console.
     
   • 3 Turn on the console to activate the controller automatically.
     
   Wireless
   • 1 Insert batteries in your wireless controller, if necessary.
     
   • 2 Hold down the "Guide" button on the controller.
     
   • 3 Push the Xbox 360's "Connect" button, located on the front of the console.
     
   • 4 Push the controller's "Connect" button to sync it with the Xbox 360.
     

Read more: How to Configure an Xbox Controller ' eHow.com http://www.ehow.com/how_7780486_configure-xbox-controller.html#ixzz1PRsAYmUA


here is a video on how to sync your wireless controller to your xbox360 console

http://www.youtube.com/watch?v=GpV-b1de2lM&feature=related

if you think this help please rate me sir thank you so much!!!

Turn off both the console and the controller, then follow these steps:

1. Turn on both the Xbox 360 Wireless Controller and the Xbox 360 console.
2. On the console, press the connect button. (to the immediate right of the memory card slot on the console)
3. On the controller, press the connect button. (Look on top of the controller for a small button.)
   
4. The green lights that surround the Guide button on the controller and the power button on the console spin and flash when the controller is being connected to the console. After the controller is connected, a single green light illuminates on the controller and on the console to show you which quadrant the controller is connected to.

Simply press the big button that has green lights around in front of your console

Is this a new controller?
Are the batteries new/recharged?

This is the sequence summary on where you are going to focus:
Step 1 - Controller
Step 2 - Console
Step 3 - Console
Step 4 - Controller
Step 5 - Both

Assuming your controller is a wireless version, Lets start!

Step 1 | Press and hold the Xbox Guide button until the controller turns on. The Xbox Guide button is the round button with the green "X" near the center of the controller.

Step 2 | Make sure that your Xbox 360 console is turned on. If your Xbox 360 console is not turned on, press the power button. The power button is the large round button on your Xbox 360 console.

Step 3 | On the Xbox 360 console, press and release the Connect button. The Connect button is the small round button on the Xbox 360 console.

Step 4 | On the controller, press and release the Connect button. The Connect button is the small button on the front edge of the controller, between the left bumper button and the charging port.

Step 5 | After the Ring of Light spins and flashes one time on the controller and on the console, the controller is connected. The quadrant on the Ring of Light that remains lit indicates the position in which the controller is connected.

Light indicator on console
Green light in the center- power is on
Green light on one quadrant - controller is connected
Four green lights rotating on four quadrants - ready to connect with controller

Light indicator on wireless controllers
No lights - no batteries
Green steady light on one quadrant - connected
Blinking green lights - its either its ready to connect or the batteries are dying

*Make sure that you have a fully recharged rechargeable batteries
*Make sure that you have a functioning/new non-rechargeable batteries
*If the steps above aren't working use another Xbox360 controller and follow the same steps.

If the new/working controller is connecting with the console this means that the previous controller is faulty - needs replacement.
If the new/working controller is not connecting with the console this may mean that the console is faulty - needs repair.

*NEVER TAMPER WITH ANY OF THE TWO AS TAMPERING WILL VOID EXISTING WARRANTY.

turn on the console. let it start up all the way. turn on the controller. on the console to the right side of the two memory card slots is a little button. press and hold it til the green lights start flashing around the power button. there is a little button on top of the controller. when the lights around the power button are flashing, press and hold the button on the top of the controller til the lights around the center button start flashing and then it should sync together

you have to link controller to xbox under disk tray to right theys a small round button press this green rings flash, whilstflashing press xbox button on controller so it also flashes this will link them

Try this:
Under heading "How can I change the screen positions for my wireless controllers?"
http://www.xbox.com/en-US/support/systemuse/xbox360/resources/supportfaq.htm

To reset the screen configuration for an Xbox 360 Wireless Controller:

1. Turn off your Xbox 360 console and any connected Xbox 360 wireless controllers.
   
   (To turn off your wireless controller, power down the system and wait for the lights around the controller's Xbox Guide button to disappear.)
2. Manually turn on your Xbox 360—don't use your controller's Xbox Guide button.
3. Press the connect button on the front of your console. This is the small button just to the right of (or below, if your console is on its side) the port for Memory Unit B. The lights around the console's power button will flash as the console searches for a wireless controller.
4. Press and hold the Xbox Guide button to turn on the wireless controller that you want to assign to slot one.
5. Once the controller is on and the lights are still circling the power button on the console, press your controller's connect button, located just to the right of the charge port.
   
   When the lights on your controller stop spinning, the wireless controller is configured to slot one and the upper-left quadrant light will glow.
6. Select the controller you want in slot two and repeat steps 4 and 5. You can configure up to four wireless controllers.