Question about RCA P61940 61" Rear Projection Television

1 Answer

TV WONT TURN ON-RCA P61950

GOT A RCA TV FOR FREE P61950, WONT TURN ON OR DO ANYTHING, FUSE IS GOOD, WHAT COULD BE SOME OF THE PROBLEMS? WHO IN THE INDIANA AREA COULD DO THE REPAIRS?

Posted by ttinch on

Ad

1 Answer

ladywinn

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • RCA Master
  • 5,138 Answers

Bad FBT! flyback transfomer.

Posted on Feb 19, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Rca p-61950 rear projection tv has pic but no sound

check your rear of the tv. there is a switch for external speakers.
1helpful
1answer

Have a rca mcr66r400 tv set found a blown fuse on the +145v line replace fuse but still tv set wont turn on! hot is good

a risistor burn out and cannot reconised the number the two sides of the Tv screen is closing in
2helpful
1answer

RCA TV wont come on

if your tv 52" silverish color hd model,problem is on power supl.deflection module(module is on left hand side),famos for number of problems,importent to indicate if green light on front panel comes on and goes off in 3-5sec.if not tv has bad fuse(put 8 amp) if blows as soon as plug it in-bad diode on the same with fuse module.
0helpful
1answer

RCA Model P61950

the fuse fl231 is not in the p611950 its in the rca chasis itc222 next to the flyback
0helpful
1answer

RCA model P61950

fl231 is the convergence fuse, and is soldered to the board in proximity of the convergence ICS, on RCA rear projection TVs.


If
fl231 has blown, TV usually does not turn on at al, if you get bowed picture, that means that the convergence ICs must be replaced.

The fuse is on the same board where you find convergence ICs, if the fuse had blown, or the pico fuses at the base of the STK convergence ics had blown, the STKs must be replaced.
There is need of purchasing the service manual to do the job.

The repair shuld be done by a technician.

This is the convergence IC, model may vary:

889c46e.jpg
0helpful
2answers
0helpful
3answers

Rca no picture no sound

There is no sound on my rca 60 tv. what can I do. The movel number is P60921.
0helpful
1answer

TV WONT WORK

have you check the switch,? cuz sometimes the switch doesn't work.
0helpful
1answer

Rca 27f630t

Hi,
It takes a star driver if I am not mistaken to take the back off probably two different sizes one for the top bottom and sides and one size for where the rca jacks are.. I only recommend checking the fuse...if blown never put foil around it. Takes a 4 amp. 5 amp would be ok. Dont go over this. If the fuse is good you should take to a good tv repairman. If blown and blows the fuse you put in take to tv repairman. Anything past this is highly technical. Hope you have a blown fuse only.
0helpful
1answer

Rca p61950 turn on and off by itself??????

Sounds like the front panel buttons are locking up the micro,unplug the unit and remove the back cover,just below were you removed the top screws you can look and see the top of the picture tubes,in fron of the middle tube is a small board,unplug the top left cable and this should restore the unit till you get the set serviced,this will not harm the set,the front buttons just wont work
Not finding what you are looking for?
RCA P61940 61" Rear Projection Television Logo

Related Topics:

388 views

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76763 Answers

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

Cindy Wells

Level 3 Expert

6356 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...