Question about Epson FX2190/NON Matrix Printer

1 Answer

All Lights blinking with beeping...

When i turn on my printer all lights was blinking with beeping and i cannot use it. what should i do to fix it? plzzz help me....tnx a lot.. and GOD blsd u all....

Posted by Jan Michael Palada on

Ad

1 Answer

Greg Cann

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,114 Answers

Looking at the manual (link below) it seems the print head may be stuck: http://files.support.epson.com/pdf/fx890_/fx890_u1.pdf Have you had any paper jam recently & not completely cleared? Perhaps something has fallen into the printer? Has the printer been moved causing the print head to be in the wrong place?

Posted on Jul 31, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i fix my LQ 680 ?


Turn off the printer and leave it off for several
minutes; then turn on the printer again.

Jul 26, 2014 | Epson LQ 680 Matrix Printer

1 Answer

When i turned on switch dell vostro 230 it give no display and led colour is red


No Display, so does it seem like the computer booted up and is running except that the Display is black? Do you hear fans running, disk drive spinning, blinking lights or beeps?

I'm going to assume that in your case since you mentioned a red light that it is not booting up all the way. Therefore your problem is probably with the memory, the video card or some other motherboard issue.

Remove the Power Cord, Remove the Battery, Remove the cover that houses the memory on the bottom of the laptop then remove one of thememory chips. Set the chip aside then try rebooting the computer. If it boots, then you know the memory chip you set aside is bad so mark an x onit with an ink pen. If it fails to boot then move the chip to the nextmemory slot and try rebooting. If it fails take the chip out and set itaside, then put the other chip in and try booting it in both slots. If itboots, just to verify that the chip set aside is bad, mark an x on it and putit into the open memory chip slot and try booting.

Apr 19, 2012 | Computers & Internet

1 Answer

Fan just work for seconds


Replace the fan or your computer will run hot and keep turning off.

Or are you saying this is what happens when you power on the computer? if so: When you press the power button do you hear fansrunning, hard drive spinning, lights on the computer, hear any beeps or lightsconstantly blinking, hear the DvD/CD drive click and the light on the drawer ofthe DvD/CD turn on for a second or two? If so the laptop is trying toboot or may have booted, but the screen is not showing for some reason.

Beep tones and blinking lights tells the technicians what is going on with thelaptop and why it is not booting. Most times it's a motherboard issuewhen you hear beeps or blinking lights continuous.

Mar 28, 2012 | Computers & Internet

2 Answers

ERROR LIGHT AND POWER LIGHT KEEPS FLASHING


dsacme.blogspot.com/2009_01_01_archive.html

Aug 27, 2010 | Canon BJC-85 InkJet Printer

1 Answer

Changed ink: on and all the lights Attention! box keep flashing


The manual for a related printer suggests that you have a printer failure issue. If the paper lights are off, then it is a scanner failure. If the paper lights are also blinking, then it's a fatal error. Turn off the printer, unplug the unit and then wait one minute. Plug it back in and turn it on, if the lights keep blinking then call HP support. (If it is under warranty, then it may be worth fixing.)

If I misunderstood your post and the power light is steady but the other lights are blinking, then you may have the cover incorrectly positioned or something blocking the ink carriage. Open it up and check for anything out of place.

I hope this helps.

Cindy Wells

Nov 29, 2009 | HP Deskjet F4100 All-In-One InkJet Printer

2 Answers

When I turn the printer power on, The lights are blinking.


  • Unplug Power Cord

  • Hold POWER and RESUME buttons

  • Plug in Power Cord

  • Release buttons after the printers starts up

  • Hold CARTRIDGE and RESUME

  • Press POWER

  • Release all buttons after the beeps

  • Press CARTRIDGE 16 times

  • Press RESUME

  • Unplug the Power cord

  • FINISH
  • Nov 12, 2009 | Canon BJC 55 InkJet Printer

    1 Answer

    Won't Print


    This is a temperature error, and may be caused by a defective print head. If replacing the print head does not fix it, the main board is defective.

    Mar 13, 2009 | Canon BJC 80 InkJet Printer

    1 Answer

    The printer apear to be dead!


    Buttons and lights on the printer Two buttons and three lights are located on the front of an HP Deskjet printer.
    • The lights tell when the printer is working or when it needs attention.
    • The buttons help control the printer.
    Buttons and lights Purpose c00123886.jpg POWER button and light Push the POWER button to turn the printer off and on. When lit, the light shows that the printer is turned on. c00123889.jpg RESUME button and light The light blinks when there is a problem with paper. When the problem is corrected, press the button. c00123892.jpg Print cartridge light The light blinks when there is a problem with a print cartridge. When the problem is corrected and the top cover is closed, the light will stop blinking. Troubleshooting blinking printer lights Blinking lights Reason c00123895.jpg

    All lights are off. The printer is off (asleep).

    Press the POWER buttonc00123886.jpg to turn the printer on.

    The printer should turn on automatically when a print job is sent to it. c00123898.jpg

    The POWER (top) light is on. The printer is idle.

    The printer is ready to print a document. c00123900.jpg

    The POWER (top) light is blinking. The printer is busy printing.

    Allow enough time to print. When a document has many fonts or graphics or uses complex color such as a color photo, it takes longer to begin printing. c00123902.jpg

    The PRINT CARTRIDGE (bottom) light is blinking. Possible causes:

    • The front cover is open. Make sure the front cover is completely closed.
    • The print cartridge is missing. Make sure the print cartridge has been installed correctly.
    • The print cartridge is broken or incompatible. Lift the front cover, and wait for the print-cartridge cradle to slide out. Check the part numbers on the print cartridge:


    Black: 51645A

    Color: C1823D,

    If the print cartridges are compatible and correctly installed, they may be defective. Try replacing the print cartridges.

    If none of the above suggestions fix the problem, and, if the error message still occurs, it may be a hardware failure. Call the HP Customer Support Center.










    Jan 20, 2008 | HP DeskJet 710c InkJet Printer

    Not finding what you are looking for?
    Epson FX2190/NON Matrix Printer Logo

    Related Topics:

    1,142 views

    Ask a Question

    Usually answered in minutes!

    Top Epson Office Equipment & Supplies Experts

    Cindy Wells

    Level 3 Expert

    6255 Answers

    Falling star

    Level 2 Expert

    217 Answers

    Kyocera HP Expert
    Kyocera HP Expert

    Level 3 Expert

    532 Answers

    Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...