Question about D-Link DKVM-2K 2-port KVM Switch

1 Answer

Wireless keyboard doesnt work with switch

I have a wireless keyboard/mouse from Labtec. When i connect the switch and boot the pc, the keyboard is recognized.But when i switch to my other pc, the keyboard/mouse isnt recognized.Even when i try to re-connect the base with the keyboard/mouse, it doesnt work. Also when i use the button on the switch,the keyboard isnt recognized anymore. I tried it with a noma keyboard/mouse and that is working fine. Does anyone heard about such a problem?Or isnt possible to use a wireless keyboard? Any help would be great kind regards, michael

Posted by mick jansen on

  • Anonymous Mar 24, 2009

    Hey You fix this Problem by re-sync it and by Holding the USB dongal or the receiver and the the connect button behind the Keyboard or the last solution is this that remove the batterys and discharge the flea Power from the keyboard by holding the connect button at the back of the keyboard . this will fix the issue

×

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Once you have switched pc you will need to re-sync the wireless keyboard and mouse with the new pc, because although you have switched pc the keyboard and mouse do not know this. there should be a reset/resync button on the bottom of both the keyboard and mouse

Posted on Jul 31, 2007

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Labtech ps2 wireless desktop


Usually, the connect procedure for Labtec is, that you press the small connect button on the receiver, (which on some models, then starts blinking).. Next, you press the connect button, on the bottom of either the mouse, or keyboard.. then repeat this, for the remaining unit.

Note: You might have to connect the PS2 receiver BEFORE starting the PC, and also might have to install the drivers, to get the multimedia-keys to work ! Good luck!

Mar 19, 2014 | Labtec Wireless Desktop Keyboard/Mouse...

1 Answer

Does the labtec wireless mouse turn itself off when not in use


Hi,
You should always safely shut down and turn off your computer before plugging or unplugging the mouse from the PS/2 mouse port. If you do not safely turn off your computer, you may damage the mouse port, the mouse, or both.

Your Labtec mouse should detect and function by simply connecting it to the computer´s PS/2 mouse port or USB port. If you have 3 Button Labtec Mouse (M/N: M-CAC64), your mouse will work in the PS/2 and serial port with the supplied adaptor. If you are using the 3 Button Labtec mouse, we recommend using the PS/2 port. To determine the model number of your device, turn it upside down and look at the label. Model numbers are indicated by "M/N:". This will help you determine what system ports your Labtec mouse can be connected to.

Thank you

Mar 14, 2010 | Labtec Wireless Desktop Keyboard/Mouse...

1 Answer

My S.O. Vista x32 doesn't recognize my mouse optical labtec 800


you can check your usb driver 

it's work or not 

you can go to control panel after that system device and hardware 
and check proper install or not 

Sep 20, 2009 | Labtec 800 Mouse

1 Answer

Activation of keyboard


Did you receive a install disk for the keyboard and mouse. typically you need to run the install disk and then plug in the usb hub for the keyboard and mouse to be recognized by the computer. If tha does not work, restart the machinew/the usb hub and keyboard and mouse ready. Are there good batteriesin the keyboard, mouse and usb hub?

May 03, 2009 | Acer Computers & Internet

1 Answer

NEED INSTRUCTIONS FOR Labtec Media Wireless Desktop keyboard , mo


This automatically shut down, but it is totally not efficient (the mouse need 10 minutes to shut down, and the keyboard can be shut down, perhaps with a keyboard shortcut (I do not know witch). My keyboard is off, and I cannot wake it up... Do you know witch tastes need to be pressed, I tried quite all, especially the connect button...

Dec 07, 2008 | Computers & Internet

1 Answer

Labtec Wireless Desktop Keyboard and mouse driver


Also check to see if you have enough memory installed as this has caused problems for others. Bud

Oct 22, 2008 | Labtec Wireless Desktop Keyboard/Mouse...

3 Answers

Connection


There is usually a "Connect" button on the devices (Mouse & Keyboard) and on the receiver the unit connected to the computer. Hit the "Connect" button on the receiver then the ones on the Mouse and Keyboard.

Hopefully that works...

If not comment back.

Aug 19, 2008 | Labtec Wireless Desktop Keyboard/Mouse...

1 Answer

Labtec wireless desktop.


Could be radio interference from somewhere. I tracked my similar mouse problem down to emissions from the ethernet adapter that connects over the house mains wiring. Try the using the mouse close to the receiver, if it works ok interference is likely.

Jan 24, 2008 | Labtec Wireless Desktop Keyboard/Mouse...

1 Answer

Labtec optical mouse


Is this a wireless mouse? If so, plug the USB connector into your computer. The pc should detect it and install the drivers automatically. Then there should be a button on the bottom of the mouse, press it, then press the button on the USB connector. This establishes a connection between the mouse and connector.

Aug 06, 2007 | Labtec Optical PS2 911544-0914 Mouse

Not finding what you are looking for?
D-Link DKVM-2K 2-port KVM Switch Logo

1,069 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4369 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...