KitchenAid KDRS807SSS Dual Fuel (Electric and Gas) Kitchen Range Logo

Question about KitchenAid KDRS807SSS Dual Fuel (Electric and Gas) Kitchen Range

3 Answers

KitchenAid KESS907 Electric Range E1 F1 Error Code

I have an E1 F1 Error Code on my range and i can not get my oven to work. How do i get that error off and my oven functioning? Please a step by step process. Thanks

Posted by patyc on

Add Your Answer

3 Answers

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,214 Answers

F1 E1, replace Electronic Range Control.

In other words, the controller board has failed.

Posted on Jan 29, 2009

Ad

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 360 Answers

Kitchen Aid Range / Stove / Oven Fault Codes Failure Code Fault Code Description Solution 4 Digit Failure Codes (for 2 digit codes see below) F1 - E0 EEPROM communication error 1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock).

Note: Applies to all F1-E... codes except F1-E3. F1 - E1 EEPROM checksum error F1 - E2 UL A/D error(s) F1 - E4 Model ID error F1 - E5 Calibration shifted F1 - E6 Latch signal mismatch error F1 - E9 Stack overflow F1 - E3 Wiring harness cavity size does not match previously stored value The "Cavity Size Select" jumpers in the wiring harness indicate a cavity size different from that which the control was previously configured for. Check the jumpers in the harness to make sure they agree with the actual oven size.

Please take the time to rate this solution.

Posted on Jan 29, 2009

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.
    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

My Viking Professional 48" gas cook top when i turn it on the flame on but the clicking 4 burner keep going on never stop.I did change new module and now turn on the 2 right burners it stop clicking when the flame on, and the 2 left burners turn on still clicking when the flame on. Please, please,help me to fix the problem. Thank you

Posted on Aug 04, 2013

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2helpful
2answers

What does error code F1 E1 mean on a kitchenaid built in oven?


F1 - E1
EEPROM checksum error

1.
Disconnect power for at least 30 seconds.
2. Re-apply power and observe for
at least one minute.
3. If code re-appears, replace control board (also
called ERC or clock).

Note: Applies to all F1-E...
codes except F1-E3.
Read full answer
Feb 14, 2011 • KitchenAid KEMC378 Electric Double Oven
tip

Troubleshooting KitchenAid oven, range and microwave error codes
Here list of Kitchen Aid range and oven codes.
4 Digit Failure Codes
F1 - E0 EEPROM communication error
F1 - E1 EEPROM checksum error
F1 - E2 UL A/D error
F1 - E4 Model ID error
F1 - E5 Calibration shifted
F1 - E6 Latch signal mismatch error
F1 - E9 Stack overflow
F1 - E3 Wiring harness cavity size does not match stored value
F2 - E0 Shorted touch pad
F2 - E1 Keypad cable connection error
F2 - E5 Cancel key drive line open
F2 - E6 Cancel key drive line open
F3 - E0 Oven temperature sensor (RTD) opened (upper oven on double oven models)
F3 - E1 Oven temperature sensor (RTD) shorted (upper oven on double oven models)
F3 - E2 Oven temperature is too high (Cook mode)
F3 - E3 Oven temperature is too high (Clean mode)
F3 - E4 Oven temperature sensor (RTD) opened (lower oven on double oven models)
F3 - E5 Oven temperature sensor (RTD) shorted (lower oven on double oven models)
F3 - E6 Drawer sensor open
F3 - E7 Warming drawer sensor shorted
F4 - E1 Meat probe malfunction - shorted
F5 - E0 Door Switch
F5 - E1 Self clean latch will not lock
F5 - E2 Latch during CLEAN error
F5 - E5 Self clean temperature not reached within 45 minutes.
F5 - E6 Door is open, but latch is locked
F5 - E7 Self clean latch will not unlock
F6 - E0 Return line not connected
F7 - E1 Common switch wire defective
Two digit codes:
F0 ERC Board failure
F1 ERC Board failure
F2 Oven temperature is too high
F3 Oven temperature sensor open
F4 Oven temperature sensor shorted
F5 ERC Board failure
F7 Function key stuck on ERC
F8 ERC Board failure
F9 Oven door lock failure
Microwave and Microwave combo error codes:
F1 - E3 or F1 - E4 Electronic control malfunction
F2 - E0 or F2 - E1 Keypad connection error
F2 - E3 Keypad held down too long, or keypad is shorted.
If you get an error code, try first resetting the code:
1. Disconnect power for about two minutes.
2. Connect back power.
3. If code re-appears, test and eventually replace faulty part.
Read full tip
on Apr 24, 2015 • Kitchen Ranges
tip

Troubleshooting KitchenAid oven, range and microwave error codes
Here list of Kitchen Aid range and oven codes.


4 Digit Failure Codes

F1 - E0 EEPROM communication error
F1 - E1 EEPROM checksum error
F1 - E2 UL A/D error
F1 - E4 Model ID error
F1 - E5 Calibration shifted
F1 - E6 Latch signal mismatch error
F1 - E9 Stack overflow
F1 - E3 Wiring harness cavity size does not match stored value
F2 - E0 Shorted touch pad
F2 - E1 Keypad cable connection error
F2 - E5 Cancel key drive line open
F2 - E6 Cancel key drive line open
F3 - E0 Oven temperature sensor (RTD) opened (upper oven on double oven models)
F3 - E1 Oven temperature sensor (RTD) shorted (upper oven on double oven models)
F3 - E2 Oven temperature is too high (Cook mode)
F3 - E3 Oven temperature is too high (Clean mode)
F3 - E4 Oven temperature sensor (RTD) opened (lower oven on double oven models)
F3 - E5 Oven temperature sensor (RTD) shorted (lower oven on double oven models)
F3 - E6 Drawer sensor open
F3 - E7 Warming drawer sensor shorted
F4 - E1 Meat probe malfunction - shorted
F5 - E0 Door Switch
F5 - E1 Self clean latch will not lock
F5 - E2 Latch during CLEAN error
F5 - E5 Self clean temperature not reached within 45 minutes.
F5 - E6 Door is open, but latch is locked
F5 - E7 Self clean latch will not unlock
F6 - E0 Return line not connected
F7 - E1 Common switch wire defective

Two digit codes:

F0 ERC Board failure
F1 ERC Board failure
F2 Oven temperature is too high
F3 Oven temperature sensor open
F4 Oven temperature sensor shorted
F5 ERC Board failure
F7 Function key stuck on ERC
F8 ERC Board failure
F9 Oven door lock failure

Microwave and Microwave combo error codes:

F1 - E3 or F1 - E4 Electronic control malfunction

F2 - E0 or F2 - E1 Keypad connection error

F2 - E3 Keypad held down too long, or keypad is shorted.

If you get an error code, try first resetting the code:
1. Disconnect power for about two minutes.
2. Connect back power.
3. If code re-appears, test and eventually replace faulty part.

Regards.
Read full tip
on Mar 27, 2010 • KitchenAid KHMS155LSS 1000 Watts Microwave...
1helpful
1answer

My oven when turned on goes to F1 and the heat is like broil...only the top burner comes on????
Hello,Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks
Read full answer
May 28, 2010 • Kenmore 40494 / 40495 / 40499 Electric...
2helpful
1answer

Oven shows error on control panel: F1:E9 - nothing works - just shows this error code. It's a KitchenAid. Thanks!
Replace the electronic range control ERC
Read full answer
Nov 16, 2009 • KitchenAid KESC307 Electric Kitchen Range
1helpful
1answer

F1 e1 error code...oven has previously cut off
F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect.
Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
#$#$
Read full answer
Oct 09, 2009 • KitchenAid KGSA906P Gas Kitchen Range
0helpful
1answer

66993 pizza oven microwave oven combo pizza oven not heating error code f1 microwave part works
Hello, please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks
Read full answer
Jul 20, 2009 • Kenmore 63662 / 63664 / 63669 Microwave...
0helpful
1answer

Can not start my oven after self cleaning proceture
F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect.
Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
%$#
Read full answer
Apr 05, 2009 • KitchenAid KDRS807SSS Dual Fuel (Electric...
6helpful
1answer

My kenmore oven is beeping and will not stop. the display shows F-1.
Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).
Read full answer
Dec 16, 2008 • Ovens
1helpful
1answer

Display
This is an error code, the error E1-F1 indicates that the Electronic Range Control/Clock has been blown. You have to get it replaced.

Sgt 48
Read full answer
Jun 04, 2008 • Whirlpool GR399LXHS Electric Kitchen Range
Not finding what you are looking for?

View Most Popular

KDRS807SSS Dual Fuel (Electric and Gas) Kitchen Range

  • Kitchen Ranges

Related Question

What does error code F1 E1 mean on a kitchenaid built in oven?

  • KitchenAid KEMC378 Electric Double Oven

Open Questions:

0answers

kitchenaid kers807sss00 got water in the control pannel
Read full answer
Be the first to answer Jan 20, 2014 • KitchenAid KDRS807SSS Dual Fuel (Electric...
0answers

"KGRC707LWHO gas range code F1E9":

Read full answer
Be the first to answer Sep 17, 2013 • KitchenAid KDRS807SSS Dual Fuel (Electric...
0answers

error message F3 E2 warming drawer sensor
Read full answer
Be the first to answer Jan 23, 2011 • KitchenAid KDRS807SSS Dual Fuel (Electric...
0answers

I got an error code of F1 (2 digits only). After resetting the power to the range, I attempted to set the correct time on the clock. It would not allow me to change the time from the default time of 12:00. The oven appears to be working now. It is a dual fuel convection range with steam assist and is three years old. Any ideas as to what my problem may be?
Read full answer
Be the first to answer Sep 26, 2017 • KitchenAid KDRS807SSS Dual Fuel (Electric...

Related Topics

4,826 views

Ask a Question

Usually answered in minutes!

Popular Questions

"set probe temp" flashing and beeping on kitchenaid wall oven

KitchenAid KESC307 Electric Kitchen...

Hi there! My Kitchenaid oven won't turn off.

KitchenAid KGSA906PSS Gas Kitchen...

KitchenAid oven shut down during self-cleaning

KitchenAid KGSA906PSS Gas Kitchen...

Kitchenaid Superba Gas Range - Oven temperature problem

KitchenAid KGST307 Gas Kitchen Range

F2e0 error on stove

KitchenAid KESC307 Electric Kitchen...

Top KitchenAid Kitchen Ranges Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22516 Answers

Brad Brown

Level 3 Expert

19166 Answers

Are you a KitchenAid Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...