Question about Andis Agc Super 2-speed Clipper International 220-volt Dog Grooming Clippers

1 Answer

My clipper smoked and now it wont run at all

Plugged in clipper, it started smoking from the blade and smelled bad, now they are dead, did they blow up?

Posted by ladyrdrhd on

Ad

1 Answer

danielle hand

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Sounds like your motor went out. You might as well buy new clippers for the price to fix them. One thing that causes that is when you spray your coolant to not hold your clippers blade up. Keep them blade down. The coolant can run into your clippers and burn them up. You only want to use grease inside your clippers.

Posted on Feb 05, 2015

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My mazda 626 has a strong potent smell coming from the exhaust


You don't mention what that smell is reminiscent of?

You don't mention the colour of the "smoke" and you didn't say whether the engine is petrol or diesel?

You don't mention whether the road behaviour/performance is normal?

White smoke is almost always steam or in the case of a diesel it could be an unburned fuel mist, grey/black is excess fuel and blue or grey/blue is burning oil.

Some steam is fairly normal until the engine and exhaust system is hot but excessive amounts could be one symptom of head gasket trouble. If the engine is drinking coolant and sending it through the exhaust as steam it will sometimes smell spicy.

Burning oil smells a bit like burned eggs in the frying pan.

If the car hasn't ultra-low sulphur oil and fuel the catalytic converter will convert sulphur traces into hydrogen sulphide - the bad egg gas...

Sep 27, 2017 | 1998 Mazda 626

1 Answer

When I engage the blades, I smell and see blue smoke, so disengaged the blade


Its not the drive belt. You have a bearing or etc. out.
I just have problem. The spindle bearing was bad.

Oct 01, 2012 | John Deere 22HP VTwin 48" Riding Mower

1 Answer

Oster A5 clippers work briefly then "pull" hair


Lever arm worn, blade blunt, or loss of movement inside the gearbox. It is possible to have a 'bad' sharpen.

Aug 03, 2012 | Oster Golden A5 Single-Speed Clippers

1 Answer

Smells like burning rubber


sounds like a bad bearing take the belt off and see what pulley is hard to turn look for the one with dark marks on it from the belt

May 12, 2012 | Craftsman Garden

1 Answer

Heater vents blow blue smoke and smell of burnt leaves


Check you cabin filter it is under hood on pass side near wiper blades
If the blower motor is running fine and no smell from there.

Dec 14, 2011 | 1992 Ford Explorer

1 Answer

I got the blades wet while my A-5 2 speed clipper was plugged in and now the unit is dead, is there a reset or fuse that requires attention ?


My best advise is to send your A5 Clipper to a professional service center or repair dealer. Because you are dealing with electricity caution is need when repairing. Manny's Sharpening has over 20 years in the clipper repair business. They have a mail order service Check his website Mannys-sharpening.com

May 11, 2011 | Oster Golden A5 2-Speed Universal Motor...

1 Answer

Cleaning Oster 78004-011 Clippers and blades


OK compressed air is perfect for your clipper, thats all it needs! Take the filters off (at the bottome of the clipper, either side of the cable) periodically and clear from excess fur. Replace. As far as the blades are concerened, Brush the excess furr off with a toothbrush or similar. Slide the cutter (smaller of the 2 blades) to one side (past half way but not all the way off!) clean exposed teeth on both blades with a bit of oil and a toothbrush, push the cutter the other way and repeat. Blade wash's tend to rust the blades, you need a big pot of WD-40. Get a 5 litre tub from the internet, only thing is there, postage will be a killer. I work for a clipper repair, blade sharpening company and we have it delivered by the truckload! Do what you do with the blade wash, but do it in WD-40. Wipe off excess afterwards and dont soak the clipper in any liquid because of electrc shock.
Thats all you can do! When your blades go blunt or clipper needs service repair: www.sheareaseltd.com If I have helped you please tell your friends about our website! Thank you!

Feb 25, 2009 | Oster Golden A5 2-Speed Universal Motor...

1 Answer

Dayton Salamander Heater - Blowing Unburnt Fuel/Smoke Randomly


I have seen this before, you need to replace the nozzle.

Feb 01, 2009 | Dayton (3E386) Heater

Not finding what you are looking for?
Andis Agc Super 2-speed Clipper International 220-volt Dog Grooming Clippers Logo

Related Topics:

598 people viewed this question

Ask a Question

Usually answered in minutes!

Top Andis Pets - Others Experts

Tom Chichester

Level 3 Expert

61336 Answers

Kardoc

Level 3 Expert

6126 Answers

Ruth summersides

Level 3 Expert

1488 Answers

Are you an Andis Pets - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...