GE EasyCam Pro Webcam Logo

Related Topics:

Question about GE EasyCam Pro Webcam

1 Answer

Ge cam my cam doesn't want to display the images on the computer. it just goes a blank green screen. i tried adjusting the colors, it still wont change. what's wrong with it?

Posted by Liz Flores on

Ad

1 Answer

electronic & computer repair& servicre

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GE Master
  • 12,061 Answers

Get a program called AMCAP, try that also ensure ya got the correct drivers. The probable reason ya see the Green Screen is because there is NO video input.. ya may have to select your camera?

Posted on Jul 18, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Sansui no signal

Acer produces a number of LCD computer monitors. Acer's monitors range from 17 inches to 27 inches. Some monitors offer wide-screen viewing, embedded speakers, high-definition visuals, and various display connection ports. Acer computer monitor problems include common issues such as dead pixels, error messages, and blank screens caused by incorrect connections. Some reviewers have also detected image problems with DVD playback on some models.

"Input Not Supported" Error Message Acer computer monitors such as the G24 may issue an "Input Not Supported" error message when users set the display resolution too high. The G24's maximum display resolution is 1920x1200 with a 60Hz refresh rate. Maximum resolutions vary according to the specific monitor model and according to the capabilities of the computer's video card. b> "Input Out of Range" b> Some Acer computer monitors may report an "Input Out of Range" error message due to incorrectly set monitor refresh rates. Much like the display resolution, each monitor also has specific monitor refresh rates with which it is compatible. Blank Screen or "No Signal" Error b> Like other monitors, Acer computer monitors feature color-coded power indicator lights. If the power indicator light shows green, the contrast or brightness levels may be set too low and should be adjusted via the OnScreen Display. If this does not rid the monitor of a black screen, the monitor may be experiencing hardware failure. The "No Signal" or "Check Cable message" may indicate a problem with the monitor's cable connection with the video card. This error may also appear on a blank screen backdrop if the monitor is plugged into the incorrect port on the computer or if the computer is frozen and needs to be rebooted. Faulty power cords or outlets may cause the screen to be black and to show no power indicator color. b> Image Issues b> Some review sites such as CNET have reported problems with streaking and ghosting during DVD playback on some Acer computer monitors such as the AL1931. (A "ghost" is an identical offset image as the primary or desired image.) Unstable or unclear image issues may be caused by incorrectly programmed VGA timings or incorrectly installed monitor drivers. b> Dead Pixels b> Dead pixels and sub-pixels can cause a variety of display enjoyment problems. Acer will only accept returns on LCD computer monitors that have "more than four (4) defective pixels per million pixels." Further, the central area of the monitor may have no more than one defective pixel. Acer does not differentiate in warranty terms between pixels and sub-pixels. Hope this helps.
0helpful
1answer

All the colors for all programs are blue and yellow on tv. have tried all the picture settings but nothing changes.

hi" do you try to adjust color settings.theres a red,blue,green color adjustment under picture setting.
try to set red color to full.
of you already do that.
probably your display driver board has a causes the problem.
display driver board produce image comes from the tuner, then it sent to x and y drive of your LCD screen.
0helpful
1answer

Hi there, my dell projector 1800mp is not projecting an image on screen and it only black lines across. what should I do to fix it?.

After turning on the projector, press "+" and "-" buttons on the control panel

simultaneously for 3 seconds and release the buttons when screen goes blank.

2 Press "+" and "-" buttons again to exit the diagnostic mode.

3While in Self-diagnostic mode, the screen will run a seven-color-cycle test as

following:

Red--> Green--> Blue--> White--> Watchet Blue--> Dark Green--> Yellow.

Ensure that the colors of the test pattern are correct. Contact Dell if the colors are
not displayed correctly.

0helpful
1answer

I have a IBM L151 LCD monitor which is 2 years old. recently while starting all of a sudden the monitor started displaying images in green color only. Secondly the horizontal images get restricted to half...

Hello,
-try the monitor on another computer and see if it will be having the same problem
-if same problem w/ a different computer it need repair
-if not the computer that you are using w/ this monitor has a problem w/ the video card --try reinstalling the video card driver
cheers
0helpful
1answer

Green horizontal

I believe that you must reset the colors of the screen by the buttons on it or try to set colors by the software that the product came with it if any. There should be a setting to configure the 4 basic colours like red green black etc. Try to adjust green. If nothing helpes go the monitor back to test it by the store you bought it if there is warranty. Hope that helped!
0helpful
1answer

Brightness/Contrast Adjustment

try going to the setup screen button left of adjustments







try going to the set up menu on the left of the buttons come down to the slider control just above the information icon then go across to color reset hope this helps regards Jim







0helpful
1answer

Lcd flat screen trouble blank screen

Please check your CPU ram I thing problem in ram.
0helpful
1answer

Monitor displays breifly then goes to blank screen

The power -inverter board probably needs an overhaul.
I redo many of these.
If the screen was pinkish or flickering before it finally got to this point, it is possible that a bulb has gone bad.
Fran
0helpful
1answer

Monitor keeps blank even the power lLED is on green

Try replacin a new display card. If it is fine working.ok
If not try fixing for cold solder in the video section.
I suggest video section according your report the light green LED lighted that shows the power section is doing fine.
Not finding what you are looking for?

109 views

Ask a Question

Usually answered in minutes!

Top GE Computers & Internet Experts

Ekse

Level 3 Expert

13435 Answers

Mehandi Husain ...

Level 3 Expert

1654 Answers

Mike

Level 3 Expert

4383 Answers

Are you a GE Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...