Hyundai ImageQuest F770D 17 in.CRT Conventional Monitor Logo

Related Topics:

Question about Hyundai ImageQuest F770D 17 in.CRT Conventional Monitor

1 Answer

Standby mode Something happened to the monitor. It stopped going to the standby mode or "save energy" mode after the computer been switched off (not the monitor). Normally it would go black in a minute! Now it keeps on, just a message comes out "No signal". Is there any way to troubleshoot?

Posted by Dmitry Goloskokov on

  • Dmitry Goloskokov Jul 16, 2007

    Thanks. You right about the video card. However I tested it with another monitor. It works fine. So something actually happened with the "Stand by" or "Power off" mode of the Hyundai monitor! Is it still possible to trouble shoot it?

×

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Check the video connection the video card. You can try another monitor to see if it does the same thing. The video card could be bad.

Posted on Jul 16, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a 51inch LG TV and never had a problem I turned it off as normal and then tried to turn it on a while later and nothing I only got a red solid stand-by light it don't flash when press side buttons...

Try following the steps below.
Step 1
Press the power button once. If the TV does not turn on, observe the LED indicator, usually located on the TV's lower front panel. If the LED indicator turned off after you pressed the power button once, it is in standby mode. Press the power button once again to exit standby and turn on the TV.

Step 2
Observe the Standby light if the remote control will not work. If the Standby light stays on, the television is in Standby mode. Press the power button on the television, then try to use the remote.

Step 3
Turn the Energy Saving Switch off, then press the power button. The Energy Saving Switch is located on the rear or side panel on most Sony model TVs. Refer to your TV user manual for the exact location of the switch.
0helpful
1answer

Black screen with.com lg logo and "energy save

this only happens when computer is on standby or there is no activity by a human like movement of mouse. it is a built-in energy saving formula on all such monitors
0helpful
1answer

Hello, Hi, I've just got myself a brandnew Dell desktop with windows 7 32 bit on it. Everything seemed to work fine, but my computer enters Power saving mode at completely random times while im actually...

The simplest thing to do, as it is a desktop computer, is go to the control panel, power options and set everything to never so the computer never goes into standby mode.
If this does not prevent the machine going into standby mode then we need to perform further troubleshooting.
1helpful
1answer

When I turn on computer, the monitor say going to dpm mode. any help?

DPMS (Display Power Management Signaling) is a standard developed to save energy and maximize the useful life of computer displays. By switching the horizontal and vertical sync lines on or off, a DPMS compliant video card provides the capability to place the monitor into one of four modes (Normal, Standby, Suspend, Off).
Each mode puts the display into a different powered state from fully powered up, to the Off mode. In the Off mode, only a small auxilliary circuit is running which monitors the horizontal and vertical signals to wake up the monitor.
0helpful
1answer

I have the screen saver set at 5,000 mins. However while I am downloading after a period of time the screen goes black. My internet connection idle time is set at 'never'. How an I resolve this?

1 check your power settings on your computer - your computer may go to standby after so many min of inactiveness. 2. check you monitor hardware setting (refer to your monitor manual) it might have built in energy save mode.
0helpful
1answer

Does not receive signal. Power saving Mode appears and that it switches to standby,

have you tried turning it on in safe mode? The F8 key at the top of the keyboard should give you that mode. Once you turn the computer on, continuously press F8 until it switches to safe mode-then go into 'control panel' and check settings for your monitor.
1helpful
1answer

LG flatron w2061tq unwanted standby power saving mode

Hi,

Go to "start>settings>control panel>Display>Screen saver>Power>

Turn off monitor : Never
System Standby : Never

I have tested and its working fine.

Thanks,
Viju
4helpful
1answer

Benq computer monitor shuts down after standby in energy saving..

There are 6 (reduced quality) capacitors in the BenQ Q9W5 which cause the screen over time to 'fail to sync' when turning on or resuming from standby.

They are;
4x 470uF 35v, and
2x 1000uF 16v.

I recommend the following replacements if you are in Australia (the ones I purchased from Jaycar only lasted 12 months);
(470uF) http://www.altronics.com.au/index.asp?area=item&id=R4865
(1000uF) http://www.altronics.com.au/index.asp?area=item&id=R5182
0helpful
1answer

Monitor keeps hibernating, can't make it stop, pixel issue.

Hey,

I think this is more of a problem on your computer instead of the monitor, ofcourse you could try another monitor and see if the same happens. I suspect your computer goes into standby or hibernation on its own, and it does work fine if you reset the computer right?

if you go into power management again, disable or turn off hibernation completely, its on one of the pages.
Make sure its not set to standby, and also disable your screen saver.

Right click on desktop - properties - then screensaver. turn it to none.

Also you could look into the computer bios and make sure its not set to standby or hibernation from there. thats unlikely but you could check.

how to get into bios.. depends on the computer, right when you turn it on, on one of the corners of the screen you will get a message, press button to enter setup or bios. press that to enter bios when its presented.

look around the bios and poweroptions.


Let me know if you need anything else.


Thanks,
Ekse
1helpful
2answers
Not finding what you are looking for?

192 views

Ask a Question

Usually answered in minutes!

Top Hyundai Computers & Internet Experts

Marvin
Marvin

Level 3 Expert

85240 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

48945 Answers

ENFORCER

Level 3 Expert

38673 Answers

Are you a Hyundai Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...