Question about D-Link AirPlus G DWL-G122 802.11g/b Wireless Adapter

2 Answers

Belkin wireless G USB adaptor 802 11g

Please help, I have completed the installation as per the cd rom but all I get is a message stating there is no wireless connection. Both computers are on Windows XP and obtain Internet connection via BT Broadband via router model Voyager210 adsl . the wireless link is required due to the second computer is in the next room, any ideas?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Correct installation of this cheap little piece of kit from Belkin might be the worst thing you ever do! If you find that Windows XP is freezing 10 times per day, just remove the wirelss adaptor and you will find that the problem disappears... The conclusion will be as obvious to you as to many other users.

Posted on Aug 03, 2007

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,961 Answers

I'm afraid, but correct me if i'm wrong but the voyager 210 is not a wireless router, it only has a wired capability. You will need to purchase a wireless router to be able to connect with the wireless adapter ypu have purchased.

Posted on Jul 13, 2007

  • andrew pester
    andrew pester Jul 14, 2007

    you can purchase a wireless router from any where but here are the BT ones
    http://www.voyager.bt.com/wireless_devic...

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I cannot connect my Belkin 54g to the internet at all. I followed the wizard and got the information from my ISP - user name and password. The wireless light works, the port shows that it working but the...


ghost2233_6.jpg Did you connect the lan cable to the right port ????

1. Shut down any programs that are running on your computer at

this time.

2. Make sure you have the following items at the computer that is now

directly connected to the cable or DSL modem. DO NOT CONNECT THE

ROUTER AT THIS TIME.

• The Easy Install Wizard CD-ROM

• The Router

• The Router power supply

• Category 5 networking cable

• This Quick Installation Guide

3. Turn off any firewall or Internet connection sharing software on

your computer.

4. Insert the Easy Install Wizard software CD into your CD-ROM drive.

The Easy Install Wizard screen will automatically appear on your

screen within 15 seconds. If it does not, select your CD-ROM drive

from "My Computer" and double-click on the file named "Setup" on
the CD-ROM.

5. Turn on your cable or DSL modem by reconnecting the power supply to The Wizard will take you through the completion of the process.

the modem.

6. Before plugging the power cord into the Router, plug the cord into the

wall, then plug the cord into the Router's power jack.

7. Verify that your modem is connected to the Router by checking the

lights on the front of the Router. The green light labeled "WAN" should

be ON if your modem is connected correctly to the Router. If it is not,

recheck your connections.

8. Verify that your computer is connected properly to the Router by

checking the lights labeled "LAN 1,2,3,4". The light which corresponds
to the numbered port that you connected your computer to should

to the numbered port that you connected your computer to should be
ON if your computer is connected properly.
The Wizard will take you through the completion of the process.

Good luck

Mar 12, 2011 | Gateway Belkin 54g Wireless DSL/Cable...

1 Answer

My web cam can only be installed on windows xp but now i have windows vista and i can not re-install it on it, can you help me please..? web-cam is the Veo Connect personal web camera. Thank you for your...


Hi Friend,
Please follow the below steps,

Step 1. Hold down the shift key on your computer to
disable the CD from Autoplaying.

Step2. Insert the Veo Advanced Connect Installation CD-ROM & Bundled Sofware CD-ROM in your CD-ROM/DVD-ROM Drive.

Step 3. Browse to the root (first) directory of the Install CD and locate Autorun.exe

Step 4. Right-Click Autorun.exe and select Properties

Step 5. On the resulting window, move to the 'compatibility' tab and tick the box labeled "Run this program in compatibility mode for:" then select "Windows XP (Service Pack 2).

Step 6. Click "OK"

Step 7. Browse back to the executable (Autorun.exe), run it and install it as per normal.

Regards,
Aysaam

Jun 09, 2010 | Veo Connect Webcam

1 Answer

Unable to Get Connectivity


Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Enabling Wireless Zero Configuration Utility

1. Please click on Start, Run and type in services.msc and click on OK.
2. Scroll down and look for Wireless Zero Configuration. Right click on it and click on Start.
3. Right click on Wireless Zero Configuration again and click on Properties.
4. Under the General tab, set the Start up Type to Automatic and Service Status to Started. Then, click on Apply and OK.

Mar 24, 2009 | NetGear RangeMax NEXT WN511B...

1 Answer

Wireless lan networking for toshiba satellite 1900


Not enough info per problem description. Not all 1900 series laptops have wireless cards installed, and not all 1900 series laptops are ready to handle wireless cards, either. Need to know what model your computer is, what wireless card you're using, ... C'mon. Let's have it...

Mar 19, 2009 | Intel Toshiba Satellite Mini-PCI Laptop...

2 Answers

Netgear wg111T Wireless Adapter 2.0 connectivity issues


Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Jan 02, 2009 | NetGear WG111U 108 Mbps Wireless USB 2.0...

3 Answers

Cant connect wirelessly


Yes u have to buy a netgear N dongle ...
Because N works on 5 ghz and G works on 2.4 Ghz
You can buy netgear WN111v3

Nov 19, 2008 | NetGear : WG111 54 Mbps Wireless USB 2.0...

1 Answer

Cannot connect to my laptop with a built in wireless.


Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Jul 13, 2008 | NetGear WG111T 108 Mbps 802.11g Wireless...

1 Answer

Wireeless


Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Feb 12, 2008 | NetGear Wireless

1 Answer

Cd driver


CD-ROM driver help CD-ROM drivers, helping you load your CD-ROM drivers on PC computers, listing what to have in the autoexec.bat / config.sys, listing different drivers .


Computer CD-ROM drive help and technical information. Complete technical help and support dealing with computer CD-ROM drives.

Good Luck if this dont do it for ya, re-install your computer back to the factory setting.

Please dont for get to Vote, Thank You.

Dec 26, 2007 | Acer Aspire 5100-5033 Notebook

Not finding what you are looking for?
D-Link AirPlus G DWL-G122 802.11g/b Wireless Adapter Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4367 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...