I HAVE FORGOTTEN THE PASSWORD TO MY HEADSET BLUETREK G2 can you please advise how i can reset this and pair to my new phone

problem with your bluetooth headset..

Your headset's pairing code is '0000' (four zeros). By the way, if you happen to miss its user guide, feel free to download it from this location.
Hope you are able to sort your problems out soon.
Regards, Carlos

try using 0000

On your phone search for the bluetrek. Once found, unplug your bluetrek and hold the button down for at least 7 seconds until you hear the tone. Then enter the passcode "0000". I have the rumor touch and this worked for me.

The passkey is 0000 (Four Zeros)

Here's the manual:>
http://65.116.253.88/mmhypercelonline/Others/SKIN_Manual_English_Version.pdf

If you found this information helpful, please give me a big thumbs up when you rate my answer. Thanks!

Switch on your phone's Bluetooth, (usually under 'connectivity'). Allow; 'visable to all'. Switch on your G2.
Phone should recognise bluetooth signal, may ask for passcode, usually; 0000. You will then get message; G2 connected.

Pairing the BLUETREK® G2
Before using the BLUETREK® G2 headset, you must pair it with your Bluetooth® mobile
phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can
communicate.
To initiate pairing:
1. Place the BLUETREK® G2 and your mobile phone within 0.3 meter (1 foot) from
each other.
2. Switch on your phone and select its Bluetooth® discover mode (refer to the
Bluetooth® mobile phone user manual).
3. When the BLUETREK® G2 is switched off, press and hold the TALK button for
about 7 seconds until the indicator light flashes red and blue alternatively. And a
sound can be heard in the speaker.
4. Once the mobile phone detects the headset, a “BlueTrek G2” message will be
displayed. Follow the phone instructions to accept the pairing. The PIN code (or
passkey) is 0000, then press “yes” or “ok”.
If pairing success, the indicator light will switch to blue and flashes slowly.
If you haven’t started the discovery mode within 5 minutes, the headset

RATE THIS SOLUTION
RNJ VINOD KUMAR

Hi - You can download the manual from the link underlined in blue below:

BlueTrek > G2



Please take a moment to rate this solution & let us know if the information given was useful to you - Good Luck!

The default password is "0000" four zeros. You can download the manual & pairing guide on the link below: http://www.bluetrek.com/support/g2/index.htm Please update the question & let us know if the information given was useful to you - Good Luck!

Just had the same problem.

But I found some bluetrek instructions on the net & it works

 

Pairing the BLUETREK® G2

Before using the BLUETREK® G2 headset, you must pair it with your Bluetooth® mobile

phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can

communicate.

To initiate pairing:

1. Place the BLUETREK® G2 and your mobile phone within 0.3 meter (1 foot) from

each other.

2. Switch on your phone and select its Bluetooth® discover mode (refer to the

Bluetooth® mobile phone user manual).

3. When the BLUETREK® G2 is switched off, press and hold the TALK button for

about 7 seconds until the indicator light flashes red and blue alternatively. And a

sound can be heard in the speaker.

4. Once the mobile phone detects the headset, a “BlueTrek G2” message will be

displayed. Follow the phone instructions to accept the pairing. The PIN code (or

passkey) is 0000, then press “yes” or “ok”.

If pairing success, the indicator light will switch to blue and flashes slowly.

If you haven’t started the discovery mode within 5 minutes, the headset