Question about Cisco 7941G-GE IP Phone

1 Answer

Ethernet Disconnected message in POE 7941G IP Phones

Hi, I am facing an issue with one of my cisco IP Phone in my office. The Phone is not connecting to the network and it is displaying a message Ethernet Disconnected. The IP Phone works in PoE Technology. Thank you in Advance. Andrew

Posted by on

  • 2 more comments 
  • Andrew Xavier Jul 12, 2007

    Hi Thanks for your Solution.
    The cable was fine.
    The IP Phone starts up as normal and it registers in the Call Manager. But after some time it displays Ethernet disconnected and the is getting disconnected from the Network.

  • Anonymous Mar 21, 2014

    wont red light isnt on when messages

  • Anonymous Mar 28, 2014

    how to connect the belkin ip phone to my skype

  • Anonymous Mar 28, 2014

    my cisco IP phone 7962 does not work unless I push the speaker phone button. Their is not sound through the handset

×

Ad

1 Answer

The first problem will be to check or replace the cable that you use to connect the phone or check the jack that you use

Posted on Jul 12, 2007

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What collaboration capabilities are available on the new Cisco 2900 and 3900 Series routers?


According to my experience and knoledge: the Cisco 2900 and 3900 series platforms have collaboration feature parity with the Cisco 2800 and 3800 Series platforms, so all of the following collaboration capabilities and solutions are present:
• Cisco Unified Survivable Remote Site Telephony (SRST)
• Cisco Unified Border Element
• Time-division multiplexing public-switched-telephone-network (TDM PSTN) and private-branch-exchange (PBX) gateways
• VoiceXML contact-center gateways
• Cisco Unified Communications Manager (UCM) media resources (allowing conferencing, transcoding, and Media Termination Point [MTP])
• Resource Reservation Protocol (RSVP) Agent
• Cisco Unified Communications Manager Express (CME)
• Cisco Unified SIP Proxy
• Gatekeeper

Cisco 3900 Series Routers

Jun 25, 2014 | Computers & Internet

1 Answer

Cisco SPA504G Firmware update issue


You need to make sure that your laptop and IP phone are on the same network subnet. For instance, if you IP phone's IP address is 192.168.2.24 than your laptop must be on the same network addressing scheme, such as 192.168.2.23.

<a href="http://www.ciscopowercube.com">Cisco CP-PWR-CUBE3</a>

Sep 07, 2012 | Cisco SPA504G IP Phone

1 Answer

My cisco wap4410n won't let windows 7 connect


Dear Romo

i have had lot's of problem with the WAP 4410N
the usual solution was to reset the Access Point
and in some case you have to reset it to factory default and set it up again try change the channel of change the location of the Access point for testing only

yesterday i face a problem with WAP4410 that the laptop gets IP but smart phone /tablet doesn't connect stack when getting an IP with static IP the devices connected


So what i did ,I went to the market and buy a new AP NOT Cisco brand


Cisco devises i lost truest on it

Abdullah Al-Ahmadi
System and Network Eng.

Mar 26, 2011 | Cisco WAP4410N (WAP4410NLA) Pre80211n...

1 Answer

My cisco ip phone 7960 is stuck in boot up mode after performing the soft reboot. i press 123456789*0#


You can try a couple of things: Unplug the power cable from the phone, hold dows the # key, and then plug the power cable in again. The phone begins its power up cycle. Release the # key after the Speaker button is no longer lit. You should see the following message on the phone: "Reset key sequence detected" Press 123456789*0# within 60 seconds after the Headset, Mute, and Speaker buttons begin to flash. If you enter this key sequence correctly, the phone displays this prompt: Keep network cfg? 1 = yes 2 = no In order to maintain the current network configuration settings for the phone when the phone resets, press 1. In order to reset the network configuration settings when the phone resets, press 2.
Or to perform a full reset: Press **#** to reset the Cisco IP Phone 7960

Mar 15, 2011 | Cisco 7910 IP Phone

1 Answer

Hi,i wanna use cisco ip phone 7940 as sip ip phone.when i power up the phone ,it can get ip from network,but finally,it shows "TFTP timeout"in display led.All the buttons can not be used.What...


Hi,

the DHCP server should be providing the address of the TFTP Server as DHCP Option 150. The most likely problems are:

Option 150 not defined, or not the correct IP address of the TFTP Server.
Or possibly your TFTP Server is not functioning properly.

If you have not Option 150 defined, the phone will use the default gateway as the TFTP server address.

Cheers, Simmo99.

Dec 29, 2010 | Cisco 7940 IP Phone

2 Answers

Cisco 1760 router had not accept password i think i forget my give me suggesion to recover it


you will have to reset it or recover it. It can be a lengthy process, here's the howto on cisco's site for a 1760 router password reset/recover:

http://ciscosystems.com/en/US/docs/routers/access/1700/1760/hardware/installation/guide/trblsht.html

Apr 01, 2010 | Cisco 1760-V Router

1 Answer

CP 7941G issue


Try configuring CCM IP address either trough DHCP parameter, or Network configuration on the phone.

Oct 08, 2008 | Cisco 7941G-GE IP Phone

1 Answer

Cicso router 1841 not connecting to the internet


When using Public IP addresses on one interface, usually facing your ISP, and using Private IP addresses (AKA RFC 1918) on another interface, usually facing your LAN, one needs to utilize network address translation (NAT) in order to connect LAN computing resources to the Internet.
Cisco has a fantastic article on how to perform the necessary procedures on their web site.
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_configuration_example09186a0080093f8e.shtml

Sep 06, 2008 | Cisco (1841) Router (cisco1841)

1 Answer

Converting Cisco 7940 IP Phone to SIP


Unlocking a Cisco 7940

Method 1:
1) Unplug the phone
2) Plug the phone back in while holding the # key
The phone will soon display “Reset key sequence detected”
3) After several lights flash press the following keys in order:
1 2 3 4 5 6 7 8 9 * 0 #
4) The phone will then ask you if you want to save the network configurations:
Save network cfg? 1=yes 2=no
5) The phone will soon display “Factory reset initiated” and will continue
through the boot up process.
If that process fails to work for some reason there
is a second method.

Method 2

Complete these steps:
  1. Press Settings.
  2. The Network Configuration lock symbol must be unlocked. If not, exit to the main window and press ** # again.
  3. Press 3 on the keypad (or scroll down) for Network Configuration.
  4. Press 33 on the keypad (or scroll down) to Erase Configuration.
  5. Press the Yes softkey.
  6. Press the Save softkey.
The phone will now be reset.

Also see this link
http://www.cisco.com/univercd/cc/td/...tain.htm#93250

May 18, 2008 | Cisco 7910 IP Phone

3 Answers

Inline power problem: cisco ip phone 7941G


You need to ensure that each port that has a phone plugged into it is configured with power over ethernet configured switched on.

Mar 20, 2008 | Cisco 7940 IP Phone

Not finding what you are looking for?
Cisco 7941G-GE IP Phone Logo

Related Topics:

3,590 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...