if you take the pins out that hold the front off it will allow you to get at the jammed staple but be careful how every thing comes apart it will not work if shims and washers are not replaced right

Posted on Mar 15, 2011

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

I need a Bostitch T5 stapler diagram so I can see what is holding the staples in. I have the stapler apart and I still can't get the staples out ?

have very old Bostitch staple gun Model T5 It has run out of staples but...

How to remove staples from bostitch T5 model only to change type of staples

Mar 08, 2018 | Staples Tools & Hardware - Others

1 Answer

What staples do I use in this staple gun? Lowes had nothing to cross reference it. Stapler calls for staples 36504-06, 36504-08, & 36504-10.

Morning!

What is the make and model of the stapler you have?

Regards
Alex Bostitchtools co uk Bostitch Nailers Staplers Fasteners Coil Nails Staples

Mar 26, 2015 | Staples Tools & Hardware - Others

1 Answer

The replacement pack for this gun say the staples are compatible with "Craftsman 68514 and 68517; Arrow Brand T50 Staplers T50 and T55; and Stanley/Bostitch TR110 and BT110 staple guns", so I assume they are also backwards compatible. That's just an assumption though.

Mar 22, 2013 | Arrow Tools & Hardware - Others

1 Answer

Stanely Bostitch 00540 stapler - How do you adjust for 15/16" staples so they do not fold over themselves in the back once you staple something. I am stapling approximately 40 pages.

There is no adjustment other than using shorter staples.

Dec 21, 2010 | Stanley Bostitch 00540: 00540 AntiJam ?...

1 Answer

How do i load the staple gun?

1 Hold stapler upside down.
2. Release black plastic catch at rear and pull out.
3. Drop staples into bottom of gun, with open side up.
4. Push black plastic catch closed and latched.

wallyp

Oct 30, 2010 | Stanley Bostitch Pc4000oc2 Outward Clinch...

2 Answers

I HAVE A BOSTITCH NARROW CROWN AIR STAPLER AND THE STAPLES ARE NOT GOING FOREWARD FOR THE ROD TO DRIVE THEM IN. IS THERE SUPPOSED TO BE A SPRING BEHIND THE STAPLES TO MOVE THEM FOREWARD. PLUNGER COMES...

There is a spring to push the staples into place. Bostitch was purchased by Dewalt and moved their parts lists to the web address below. Enter your model number and order the parts needed. Good luck with your future projects.
http://servicenet.bostitch.com/

Sep 02, 2010 | Stanley Bostitch STB-MIIIFS Flooring...

3 Answers

Where can I download a manual for Bostitch T5 Staple Gun

If you want to know how to load the staples, lift the wee flap at the end with the inscription " lift to insert staples".....

Jan 23, 2010 | Stanley Hand Tools

1 Answer

Bostitch nail gun number SB-21n1 is jammed and need manual to know how to unjam it or a solution online. Was using it in the staple mode and it jammed after about 5 staples. Was using bostitch staples.

Hello. Begin by disconnecting the air hose. That way you can not get hurt while removing the jam. Get a pair of needle nosed pliers and remove each of the jammed staples. They will pull out I assure you. Then Use a little WD-40 or compressor oil to lubricate the working mechanism at the firing head. IF you must loosen up the mechanism to remove all of the staple parts be sure to use the correct size allen wrench. I am providing link to a free manual for your gun in case you don't have one: http://bostitch.com/catalog_images/web_pdf/107674.pdf

Jan 12, 2010 | Stanley Bostitch 18 Gauge Brad Nailer 1 -...

4 Answers

I have a bostitch M3FS floor stapler that only puts out a staple every 10-15 hits. I've opened it up, cleaned it out, oiled it as recommended with air tool oil, and I can get a few staples out of it, but...

You could try finding your stapler and repair solutions oneReplacementParts.com They have parts, and guides to help repair this stuff.

Aug 10, 2009 | Stanley Bostitch STB-MIIIFS Flooring...

1 Answer

Staple gun

Open the chamber and drop the staples upright in to the chamber do not try to load the staples by placing them on the strip that pulls out as you do with most staple guns.

Oct 26, 2008 | Stanley Bostitch Pc2000 Staple Gun Tacker...

Not finding what you are looking for?

View Most Popular

Tools & Hardware - Others

I need a Bostitch T5 stapler diagram so I can see what is holding the staples in. I have the stapler apart and I still can't get the staples out ?

Staples Tools & Hardware - Others

Open Questions:

0 Answers

Wagner 915 steamer. Why isn't it getting power? Turn on no light or sound. Power button never lights up

Jan 03, 2021 | Tools & Hardware - Others

0 Answers

7313 belt sander. What is the keyhole slot for?

Jan 02, 2021 | Skil Tools & Hardware - Others

0 Answers

Why doesn't it fire? A slow blinking light. Once depressed, steady light & the fan runs. Press trigger, then nothing. I've replaced batteries and 2x O rings

Dec 30, 2020 | Hitachi NR90GC2 Cordless Gas Clipped Head...

0 Answers

Model DC618 nail gun. Why does it start, then shuts down as soon as I depress to fire nail?

Dec 27, 2020 | Dewalt Tools & Hardware - Others

Ask a Question

Usually answered in minutes!

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual

Where can I get replacement staples for bostitch model t10 staple gun

1 Answer

jdlc