Unable to install harness after washing

I took the covering and harness off to wash it. Now I am unable to install it. I dont know were anything goes. Please please help.

Anonymous Nov 12, 2011

how to install harness for cosco carseat

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Problem Solver:

An expert who has answered 5 questions.
Contributor
9 Answers

You might be able to contact Cosco for a manual or diagrams of where everything goes, there info is: Consumer Relations Department at 1-800-544-1108 Hours of operation Monday ? Thursday 7:00 AM to 6:00 PM EST and 7:00 AM to 4:30 PM EST on Friday.

Posted on Jul 19, 2007

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1helpful

1answer

My 7 kg hoover washing machine started sparking underneath then it stopped & unable to start.

There is a common issue with those machines and the wiring harness, when the machine spins, the drum causes the wire harness to flex and vibrate and this can cause the wires to break loose. To check this you need to unhook and unplug the unit and drain it, Then you can lay it down and look under it to see what is causing the issue;

Read full answer

Jun 11, 2021 • Hoover Washing Machines

0helpful

1answer

Frigidaire dishwasher model FDB520RHS2 will not advance pst wash- just keeps washing draining and refilling the wash. does not advance. Left it run for 3 hours, still wash only

We had a problem with our dishwasher, it just went crazy one day and lights would light up but ours did not wash or anything...anyways upon further investigation found out by taking 6 large round head screws off,, the handle and outer cover came off, then there was a cover that was covering a circuit board and this was the brains of the washing machine, ordered the part from sears 160.00 and washer is all set. good luck. oh ya, upon further exam. when I took the board off could see discoloration on part of the circuit board. this means burned out resistor or fuse.

Read full answer

Mar 22, 2014 • Frigidaire Dishwashers

0helpful

1answer

I took the straps out to wash the cover and i didnt pay attention to how i took them out and now i dont know how to put them back on

straps on what

Read full answer

Mar 26, 2011 • Cycling

0helpful

1answer

Hotpoint W321 flashing lights - washing machine

I have the same machine and it's the 2 solenoids for the cold water inlet at the back. I took the top cover off with 2 screws at the back and the 2 solenoids are connected by 2 screws. I dont know the price as i cleaned mine by flushing fresh water through and the spraying a little wd40 into both parts and it works fine now or just buy new part it's easy to fit but make sure always the mains is disconnected.

Read full answer

May 04, 2010 • Washing Machines

0helpful

1answer

Need to install new safety switch but am unable to get front cover off the washing machine. I can get it off the 2 top plastic clips but where are the other clips at the side or bottom of the washer.

You are the one looking at it and no one can guess what you see or dont see.
Get a techo to have a look......if you cant find how to dissassemble something......what competence level are you bringing to the fitting of a safety switch??

Read full answer

Oct 19, 2009 • Washing Machines

2helpful

2answers

I took the cover almost off and now don't know how to put the harness back together

have you received an answer yet??? I have had to take off and put back on mine at least 10 times now.....If you still don't have an answer I will take mine apart and re-cover and write steps down as I go....it is a hard cover to take on and off....it still takes me about 20mins to get it all together....you may want to consider buying a easy remove cover to go overtop of your pre-existing one. Let me know if you need help

Read full answer

Jun 28, 2009 • Cosco Alpha Omega Elite 5-Point 22-155

19helpful

1answer

Harness straps off cosco car seat to wash cover, help reattaching

I need help putting the straps back on a Cosco 5-point car seat. Took it apart to wash and can't get it back together

Read full answer

Mar 08, 2009 • Century Encore 5-point Harness

0helpful

1answer

Whirlpool ultimate careII spin cycle

sounds as if perhaps a wire is off on the side of the motor assy, l;ook at he wiring harness, sometimes a "chugging " noise occurs form the motor when one of the harnesses is not attached. and yes its normal to wash with the lid open, not to spin however( thats a saftey issue)

Read full answer

Jan 21, 2009 • Whirlpool Ultimate Care II LSQ9564J Top...

0helpful

1answer

Need to remove lining from Matrix Cup

i have just bought one of these second hand so wanted to wash it all. No problems doing it at all. All clean & new ready to go. (put it on handwash in washing machine) It took me a while to work out how to get certain bits off but easy once you know how. Hope this helps x

Read full answer

Jan 09, 2009 • Jane Powertwin Jogger

0helpful

1answer