Question about Marantz SR-4200 Receiver

2 Answers

No output from left channel after crackling sound

Crackling sound commenced a week ago, & now there is no sound at all from the left channel. Re-configured the speaker setup & still occurs. Swapped the speakers around & it was still happening on the left channel. Model is SR-6200.

Posted by on

  • Connie Ciciulla Jul 13, 2007

    Volume Knob, but we mostly use the remote. Any ideas ?? Much appreciated :)

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.
    New Friend:

    An expert that has 1 follower.
    Mayor:

    An expert whose answer got voted for 2 times.
    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Marantz SR 5200/6200 lost audio or crackling on left or right channel except in mode s-direct is now fixed !
The root cause is a defective inegrated circuit on DSP board (the one with digital inputs). To fix it change the chip CS4391 by a new one or better by the improved version CS4392. On my device a capacitor was cut close to this IC : replace one 1uF after changing the IC. For any question search me with my callsing "F5RCT"; i have a spare IC for the one who is able to change it !
I'm amateur radio and engineer

Posted on Jun 18, 2013

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points
    MVP:

    An expert that got 5 achievements.
    New Friend:

    An expert that has 1 follower.
    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 83 Answers

Does your unit have a volume knob or is it a paddle type with up and down?

Posted on Jul 12, 2007

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

6ya.com

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Onkyo TX-SR876 receivers gives popping and crackling sounds from its front left and surround right channel. I tried it with different input/source but the output is same. but sometimes it works ok with...
Perhaps you must check out wires for speakers and contacts on receiver and speaker.

Mar 09, 2016 | Onkyo Tx-sr876 7.1 Channel Home Theater...

4 Answers

Subwoofer
go to audio set up and configure the system for 5.1 or higher sound output.then only all the speakers ll work

Jan 03, 2008 | Yamaha RX-V640 6.1 Channels Receiver

1 Answer

I only have left channel on speakers working have tested speakers ok, swapped pre amp boards still one channel, swapped output boards the same. What could it be? Barry
is there Sound stage output is stereo if stereo then one side is missing or broken link from ic to speaker, If mono output then use with one side 2 speaker parallel.

May 20, 2015 | Audio Players & Recorders

1 Answer

Have noise on left back speaker channel of onkyo 606 blocking sound from movies etc
Hi Brendan, have you swapped the speaker from the left channel to the right one so that we can be sure that it is not the speaker? You can also try a hard reset:

To do the reset you need to turn the receiver on, then on the front panel of the receiver press and hold the "VCR/DVR" button while doing that press the "STANDBY/ON" button. You will see the word "Clear" in the display screen and the receiver will go into standby mode. PLEASE UNDERSTAND THAT YOU WILL LOSE ALL YOUR AUDIO & VIDEO ASSIGNMENTS ON THE RECEIVER PLUS YOU WILL LOSE ALL YOUR SPEAKER CONFIGURATIONS, SPEAKER DISTANCE AND ALL LEVEL CALIBRATION SETTINGS. YOU WILL ALSO LOSE ANY PROGRAMMED RADIO STATIONS IN MEMORY. Once the receiver goes into standby mode turn it back on and go thru the setup menu for all custom settings.

To do the reset you need to turn the receiver on, then on the front panel of the receiver press and hold the "VCR/DVR" button while doing that press the "STANDBY/ON" button. You will see the word "Clear" in the display screen and the receiver will go into standby mode. PLEASE UNDERSTAND THAT YOU WILL LOSE ALL YOUR AUDIO & VIDEO ASSIGNMENTS ON THE RECEIVER PLUS YOU WILL LOSE ALL YOUR SPEAKER CONFIGURATIONS, SPEAKER DISTANCE AND ALL LEVEL CALIBRATION SETTINGS. YOU WILL ALSO LOSE ANY PROGRAMMED RADIO STATIONS IN MEMORY. Once the receiver goes into standby mode turn it back on and go thru the setup menu for all custom settings.
If you need further assistance please email me at [email protected], Thanks,JT

May 04, 2015 | Onkyo Audio Players & Recorders

1 Answer

C370 faint crackling sound left channel
have you tried looking at your phono leads,turn volume down until it is low enough that you can still hear the music playing,give the phono leads a turn to see if its a loose connection.if not,try the right channel phono in the left channel to see if this fixes your problem.also you could do the same with your speaker leads and see if that solves the issue.maybe a bad connection is the cause?.it may also help to try and move your cd player away from your amplifier.it could also have been overdriven (played too loud for too long) on the night of the party,only you will know if this was the case or not.

Jan 07, 2013 | NAD C370 2-Channel Amplifier

1 Answer

Only one of four speakers puts out sound!
Check all your RCA"smake sure they all have output..Then use a fluke metere, or any meter you can get that tests ohms, and measure each speaker..they should all read arround 4. If the outputs from the deck are good, and the speakers measure correctly, then you have got yourself a bad amp.

Jul 29, 2009 | Kicker (ZX350.4) Car Audio Amplifier

1 Answer

Right channel won't play on stereo amplifier
In old stereos the first things I look at are output transistors, solder joints and electrolytic capacitors. If you know how to solder, bad solder joints are pretty obvious. If you need a tutorial on how to spot bad solder joints, look here.

http://www.kingbass.com/soldering101.html

As for bad caps, look here. The info is aimed at computer motherboards but still helpful.

http://www.badcaps.net/pages.php?vid=5

Dec 06, 2008 | Audio Players & Recorders

1 Answer

Sound only from left and right channels
ola a todos la verdad no incuentro nada de lo que quiero asi que no busquen nunca en esta pagina pq vale callampa ok xao de eric

Sep 21, 2008 | Creative Labs Sound Blaster Live! 5.1...

1 Answer

Yamaha rx-v2200 sound problem
Hi Zanthena - my Yamaha rx v 2200 is doing exactly the same thing - did you manage to track the problem down? I have had my unit in for repair and the fault occurred again 6 hours after I re-installed it.

Any help would really be appreciated!

Jason.

Sep 07, 2008 | Yamaha RX-V2200 Receiver

1 Answer

My speakers have almost constant crackling noises
Hello, there is no chance that you can fix this problem by replacing speaker wires. Resoldering the output stages as well as area around the microprocesor could be the efficient solution. If you need more info please advice.

Apr 12, 2007 | Sony DAV-BC150 System

Not finding what you are looking for?

View Most Popular

SR-4200 Receiver

  • Audio Players & Recorders

Related Question

My Onkyo TX-SR876 receivers gives popping and crackling sounds from its front left and surround right channel. I tried it with different input/source but the output is same. but sometimes it works ok with...

  • Onkyo Tx-sr876 7.1 Channel Home Theater Receiver black

Open Questions:

0 Answers

marantz sr 301 remote code

Feb 01, 2014 | Marantz SR-4200 Receiver

0 Answers

Marantz SR-4200 will not change to digital from analog

Oct 28, 2010 | Marantz SR-4200 Receiver

0 Answers

Marantz SR4200 Subwoofer Not Working I've had my Marantz SR4200 Amp for years now and have only recently tried to connect a brand new subwoofer (Eltax Liberty S+) for the first time. I cannot get any output from the subwoofer at all. I have connected using the manual and changed all the appropriate settings on the Amp so that subwoofer is on etc. but nothing. I've connected the new sub to my PC sound system which had an existing sub (broken) and it works fine. I'm concious that I may need a special cable? or that it might just be a fault subwoofer port on the Amp? Any advice would be appreciated, thank you.

Feb 21, 2009 | Marantz SR-4200 Receiver

0 Answers

how do i hook up wii, cablebox, dvd, tv, to my Marantz 4200 I have sound no picture

Dec 31, 2008 | Marantz SR-4200 Receiver

Related Topics

Marantz SR-4200 Receiver Logo

Related Topics:

855 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Marantz Audio Players &...

Marantz SR-92 Mark II Receiver

Marantz Audio Players &...

Marantz Audio Players &...

Marantz PMD660 Digital Voice...

Latest Celebrity Headphones Report
Latest Celebrity Headphones Report

View all Fixya Reports

Top Marantz Audio Players & Recorders Experts

The Knight
The Knight

Level 3 Expert

76204 Answers

Grubhead
Grubhead

Level 3 Expert

5699 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Marantz Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. SR-4200 Receiver Manual

SR-4200 Receiver

Loading...