Question about Whirlpool GU2400XTP Built-in Dishwasher

2 Answers

Its not working at all!

Hi we have a Whirlpool Quiet Partner III, model #GU2400XTPB1, and it does not run at all, and the clean light is blinking green. For the past few months before it went out we noticed that it was getting louder and louder as it ran. Then it went completely out. Help! Not sure where to start. Thanks! mglass

Posted by Marissa... on

Ad

2 Answers

Anonymous

If the clean light is blinking, the heater circuit is out.

Posted on Aug 13, 2007

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.
    Corporal:

    An expert that has over 10 points.
    Mayor:

    An expert whose answer got voted for 2 times.
    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Sounds like the main wash/circulating pump is faulty

Posted on Jul 12, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to diagnose whirlpool quiet partner iii
The clean lite blinks out a code when a fault has occurred . Inside the bottom access panel is a booklet with the list,

Jun 03, 2014 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Quiet partner whirlpool III gold reset
TRY A RESET CODE
Press the "Sani Rinse," "Heated Dry," "Sani Rinse" and "Heated Dry" buttons on the dishwasher's electronic control panel in quick succession to put the appliance in diagnostic mode.
Close the dishwasher door and engage the door latch.
Wait 10 seconds before pressing the "Cancel" button to reset the dishwasher.

Dec 18, 2013 | Whirlpool Gold Dishwasher with Quiet...

1 Answer

Whirlpool quiet partner III pots & pans light blinking, and the time remaining indicator has two horizontal lines in it-it wont shut off and it wont start. Tried shutting off power for a few hours,...
test

Nov 01, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

2 Answers

Whirpool dishwasher quiet partner 2 clean light blinking wont cancel or run a cycle
Hello,

press normal heated dryer normal heated dry normal the dishwasher should reset and start. You will need to check the heater this happens because the heater normally fails. Let me know,

http://www.appliancerepairlesson.com/

Mar 07, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Our quiet partner iii dishwasher is not working. It is not gettting dishes cleaned soap left on dishes
Our whirlpool gold quiet partner iii dishwasher is not working well . It is not gettting dishes cleaned soap left on dishes on top primarily

May 16, 2010 | Dishwashers

1 Answer

Whirlpool quiet partner III. Clean light keeps flashing clean.
Had the same problem. Press the sani-rinse and heated dry button back and forth and it should reset.

Aug 29, 2009 | KitchenAid 24 in. KUDI02IR Built-in...

1 Answer

Clean light flashing Quiet Partner V
do the heated dry and hi temp and then hitr cancel. you know what this means?! you have a bad heating element usually. call for service this should be a covered repair if it is only 6 months old

Mar 26, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

RUN TIME ON NORMAL WASH IS ABOUT 3 HOURS
common failures on that usually are the heating element. Look at the botton and see if it is broken anywhere.

Mar 22, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

7 Answers

Whirlpool gold- quiet partner III
An angel of mercy on another blog posted this solution and it worked for me as well. My Whirlpool Quiet Partner Dishwasher would not work due to the CLEAN light flashing in 7 interval sequences. I followed these steps and my dishwasher is not working perfectly...hope it works for you:

"Well for mine which is a Whirlpool Gold Model # GU2400XTPS3, I found the seq of buttons that I had to push to reset the curcuit board. I think it may of been in this forum somewhere. But I had to push - Sani Rinse, Heated Dry, Sani Rinse, Heated Dry, and then the dishwasher went through it's diagnostic cycle and then after that the light stopped blinking and the dishwasher works great. Supposily, there is a Product Tech Sheet behide the kick panel of every dishwasher, but mine was gone so I had to find the information on the internet. You might want to do a serach for the correct seq of buttons you have to push to reset the curcuit board. If you know for sure that the heating element is bad, you will have to order one. "

Mar 04, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?

View Most Popular

GU2400XTP Built-in Dishwasher

  • Dishwashers

Related Question

How to diagnose whirlpool quiet partner iii

  • Whirlpool GU2400XTP Built-in Dishwasher

Open Questions:

0 Answers

Why is wash cycle flashing. Cannot turn off?

Oct 19, 2014 | Whirlpool GU2400XTP Built-in Dishwasher

0 Answers

How old is dishwasher gu2400xtp

Jul 22, 2014 | Whirlpool GU2400XTP Built-in Dishwasher

0 Answers

Dishwasher does not turn on

Jul 06, 2014 | Whirlpool GU2400XTP Built-in Dishwasher

0 Answers

Light blinks and won't turn on

Jun 30, 2014 | Whirlpool GU2400XTP Built-in Dishwasher

See all Whirlpool GU2400XTP Built-in Dishwasher Questions

Related Topics

Whirlpool GU2400XTP Built-in Dishwasher Logo

474 views

Ask a Question

Usually answered in minutes!

Popular Questions

4 Answers
Whirlpool dishwasher reset code

Whirlpool 24 in. GU3200XTP...

12 Answers
WHIRLPOOL DISHWASHER, ERROR CODE 4,

Whirlpool Dishwashers

7 Answers
Whirlpool gold- quiet partner III

Whirlpool GU2400XTP Built-in...

8 Answers
Whirlpool quiet partner III clean light blinking green

Whirlpool GU2400XTP Built-in...

9 Answers
Gritty white film all over dishwasher and dishes

Whirlpool GU2400XTP Built-in...

Top Whirlpool Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Mike

Level 3 Expert

4376 Answers

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...