Question about Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A, 9.6v 1000mAh NiMh Pk 2-Way Radio

Kenwood 79a dual band transiever

The problem i am having is my 79a display flickers. everything elso works well. I went through the book and the schematic and came up with a possible fuse in the power section but im not sure. is there a fix for this? thanks

2 Answers

Anonymous

I had the same problem. Cleaned and re-seat the flex cable. Works fine now.

Posted on Oct 08, 2007

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Governor:

An expert whose answer got voted for 20 times.

Hot-Shot:

An expert who has answered 20 questions.
Expert
123 Answers

There are several reasons for this, but one can be the flex that joins the display with the circuitry, carefully check if this is not broken or in this process or dirt.

Posted on Jul 03, 2007

1 Suggested Answer

6ya staff

2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

Upload

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

UNLOCKING RF KENWOOD TH255A

its illegal

Feb 13, 2014 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

I have two Kenwood TH-79A Transceivers. Both of them have the common "flickering display" problem. My eyes are no good and I can no longer accomplish this relatively easy repair. Who can do...

SORRY but FIXYA has no clue as to who can do this , even if it costs both arms .

Dec 26, 2017 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

My TH79 only shows channel numbers, what is the fault???

You should be able to enter the menus and change the freq display mode away from "alpha".

Jun 19, 2010 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

TH-79A Blank screen. It works with "F-switch on" but then goes blank.

Happened to me too. It takes some disassembling!!!! Between the screen and the underlying circuit board is a rubber strip with conductive material throughout which provides ''ground' for the display. This rubber wears out over time, but the quick fix is to turn it a quarter after cleaning and treating the contact surface with 'contact spray'( sparsely!!).

Job requires steady hand and pincers.

May 28, 2009 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

I don't have a screen display on my TH-79A. The radio is usless in this condition. Has anyone else had this problem and what was your fix?

You could have a defective screen or a defective LCD driver, either way you have to replace it.
I 've replaced LCD screens before they typically are the entire front half of the radio inside wise. Probably going to cost a few to do it.

Mar 12, 2009 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

My th-79a shows channel numbers only

RTFM Page 29

Press [BAND] + POWER ON to toggle Channel Display

Gerard - PE1OUD

Mar 04, 2009 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

Unlocking Kenwood TH-22AT

http://www.radiomods.co.nz/kenwood/kenwoodth22.html

Dec 20, 2008 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer

TH-79A amateur radio

TH-79A Kenwood HT and with the power off, hold down the MR button and the PTT switch, and while holding both of these turn on the power. The HT will come up in the remote control mode with the display indication "RC" on one band and the normal display on the other band.
.
To get the HT out of the "RC" mode just repeat the MR+PTT+Poweron sequence

Oct 30, 2008 | Kenwood PB-34M, ,TH-22AT,TH-42AT,TH-79A,...

1 Answer