I need a replacement Teknique remote control

It may be that the code used to program the one for all remote isn't quite the right one for the freeview box.
Have you tried looking on the one for all website for any new codes for your box?

reset the code go to www.fitness.manualsonline.com or www. remotecodelist.com

God bless you

Not all Universal remotes can work with your Freeview Devices. You need to find one that will work for your specific device AND your TV. Many Universal Remote Designs predate Freeview construction so a lot of them only have basic function. You need to Google the model number of your Freeview Receiver AND "Remote" to get a remote that will operate it.

Very common and yes probably irritating too. Sometimes technology just doesn't evolve as fast as others do. This is unfortunate. Wish you good luck!

OK - please follow these instructions carefully to setup the Freeview box. If you get stuck at any point in the instructions - or anything I've said doesn't make sense or match what you can see - just post another message here and I'll deal with each problem as it arises.

1. Switch the TV and Freeview box to STANDBY. There should be a red light on the Freeview box;
2. Connect the aerial cable to the freeview box. Make sure you are connecting this to the correct socket. This should be labelled "RF IN", "IN" or "Aerial/Antenna". If you have connected to a socket marked "RF/TV OUT" or "TO TV" or something similar, it wont work;
3. Connect the SCART cable to Freeview box and the back of the TV;
4. Switch the TV on;
5. Switch the Freeview box on - you should get a green light on the front of the box;

Most TVs will automatically switch to the external input when a SCART device is switched on while the TV is already on. This is why you should switch the TV on first.

At this point you should be able to see the installation / setup screen for the Freeview box displayed on your TV. If you cannot see this:

A. Press the INPUT button once on your SAMSUNG remote control once. This is the button in the top-right corner of your remote control.
B. If you still cannot see the installation / setup screen, press the MENU or SETUP button on the remote control supplied with the Freeview box.

The instructions from this point forward will be different if you had to press the MENU / SETUP button on the Freeview remote before anything appeared on the TV screen. If this Freeview box has been used before the installation screen will not appear, but you will get at on-screen menu after pressing the MENU / SETUP button. If this happens, please let me know and I will provide alternative instructions for setup.

Assuming you have been able to access the installation screen, it should be easy enough to follow the instructions on screen from this point. Use the UP / DOWN / LEFT / RIGHT arrow keys on the Freeview remote to highlight the relevant options and then press OK / SELECT to choose that option.

I don't want to make this too complicated by providing alternative instructions for every possible scenario. Please run through the instructions above and make sure you are getting an installation screen or "menu/list" displayed on the TV. If you need further instructions from there, I will provide them in another message.

Good luck - I'll await your reply.

Regards,
BElectric

matsui freeview has any one got the code for this total control URC11 2840r00

go online and google it

im looking for sagem freeview code on total control.
thank you

Hey there,

I don't know for sure, but this might help. I asked a question myself then managed to find my own instruction sheet. My question was about the 'auto find' function where the remote tries all codes until you find one that works and store it. Hope it helps!

==
This is it's instructions in case they help anyone else. By the way where it says 'a second or even a third time' be prepeared for many more attempts than 3!!

==
First power on the equipment to be controlled. Press the SET button and don't release, then press the equipment control button (such as tv / vcr etc). The red light will be on. Release the SET button then press the SET button again, the red light will be flashing. Press the POWER button, the remote controller will transmit a signal to power off the equipment. If the equipment cannot be powered off for the first operation, try a second or even third time until the equipment is powered off. When the equipment is powered off, the code will correspond with the equipment. Press the button for the equipment (such as TV) to save the setting.

hi can anyone HELP I HAVE COBOLT JUMBO REMOTE BUT NO CODE FOR ACCER LCD

i have the instruction but can scan the basics but pages of codes. let me know what brand you need.