Question about Whirlpool 24 in. GU3200XTP Built-in Dishwasher
I have a whirlpool dishwasher just over a year old and the clean light keeps flashing and I can't get the dishwasher to start, if I select the cancel button it runs for a couple of minutes but the clean light continues even with the door open or shut, all the buttons work if pushed but nothing happens.
Yust reset press heated dry-normal-heated dry normal-and it will work 100% remember that code it is reset code for wirpool quiet partner and many other models
Posted on Feb 19, 2009
you just save me and my wife a 129.00 service call. this is the strength of people like you and many others that help people at trying times.may God bless you!
Thank you so much! Worked perfectly. I was just about to call the repair man and thought I'd look it up first. I would have never known! :)
Wow; just tried this and it totally worked. So grateful for you help! Thank you! My just over a year whirlpool stainless steel dishwasher clean light would not quit blinking and it would not start. I looked in the manual and it said to call the repair man. Also looked at e-how; said the same thing. I tried your directions and they WORK! Now why couldn't whirlpool put this in the manual? Just wondering...
thank you!!!!!!it work.....
Holy Cow ! ! Thanks to you my dishwasher is working again ! ! Bless You ! !
You, my friend, are a God Send! Finally, clean dishes!! Thank you so much!!
thank you so much clean light no longer blinking,worked exactly as you said,btw my dishwasher whirlpool less than a year old.
OMG!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! BRILLIANT!!!!!!!!!!!!!!!!!!!!!!!!!!!!
×
Reset worked for me. I had the same problem as others. Thanks for your help.
Posted on Nov 10, 2008
Flashing clean only means that the water didn't get hot enough at some point during the cycle. Are your dishes dry at the end? If not, it's the heater element, these will run you about $75.
If they are dry, then you're just not getting enough hot water into the washer. Make sure it's not connected to the cold water supply... (it happens)
You probably won't find that tech sheet. They stopped doing that years ago.
Posted on Dec 29, 2007
I had this same problem and had to have a tech out to look at it. It is a heater issue, but all he did was reset the dishwasher using the sequence mentioned above. What he told me was that the water temperature was not getting hot enough and suggested I run the hot water on my sink until its hot so the dishwasher immediately pulls senses water. The light came on the first time after about a year. It recently came on again and I reset the dishwasher again. Hopefully it won't happen for another year. BTW, I don't run the hot water at my sink and if I have to reset it once a year, so be it.
Posted on Sep 03, 2007
The flashing clean light is usually an indication of a problem (error code). There should be a tech sheet inside the lower kick panel under the door. The tech sheet will give you details on what to do to clear the problem and/or troubleshooting advice. The flashing clean light may also be in conjunction with other indicators on the front panel. When reading through the troubleshooting section pay close attention to see if there are any other indicators lit at the same time. This will narrow down the error to a specific problem. I wish I could be or more help, but there are several different models that indicate errors in the same manner and mean different things. I hope this may be of some help to you.
Posted on Jul 02, 2007
Thank to all of you! I did the sequence thing, and my washer is working!!! Yea!
Posted on Aug 20, 2010
Push the following buttons in this order within 6 seconds:heated dry, normal, heated dry, normal. This will restart the dishwasher but you need to check the heater in the bottom.
Posted on Sep 02, 2007
I have this problem ,the normal light is flashing and dishwasher not working
Posted on Apr 02, 2011
The reset codes work but you might need to power cycle the dish washer. If you don't have a switch for it be sure you know what braker it is on.
Posted on Apr 03, 2009
I have the same issue except that every time I run a load after a reset it does the same thing.
Posted on Jan 16, 2013
Hitting HD/N/HD/N worked perfect, I did have to do it twice.
Posted on Jul 10, 2011
Start resume light continues to flash the dishwasher will will start on its on and run for a few seconds and then shut off light continues to flash
Posted on Sep 17, 2009
SOURCE: whirlpool quiet partner III. Clean light keeps flashing clean.
Had the same problem. Press the sani-rinse and heated dry button back and forth and it should reset.
Posted on Dec 29, 2009
SOURCE: Clean button will not go off
Alternate solution: Within 6 seconds, alternately press "heated dry" then "normal" buttons. Wait for all lights to come on and for the diswasher to finish washing the load.
Posted on Aug 19, 2010
SOURCE: Need help with dishwasher
I misplaced my diagnostics paperwork, but I found you here and you saved my life! The wife is much appretiative! ~Teddy Bear
Posted on Oct 20, 2007
SOURCE: clean light flashes
You will have to reset the console. To do this, close the door and press these buttons in sequence...
-high temp wash
-heated dry
-high temp wash
-heated dry
...all
the lights will turn on briefly and the machine will start a diagnostic
cycle. You can press cancel or let the diagnostic cyle finish (1-2
minutes).
You should now be able to run the dishwasher as normal.
Posted on Feb 20, 2009
6,684 views
Usually answered in minutes!
I am having the same problem the dishwasher is not even a year old. The clean light keeps flashing and only when I hit the cancel button it keeps a noise and then shortly stops.
same problem here... it's happened a few times and I've had to have the repair man come in to fix it.
Not impressed! Would not buy this product again.
We have the same problem light flashing
i have the same problem but after doing the reset code i tried to run a load and now my start light flashes and the dishwasher won't turn on
×