Metrologic Instruments MS7120 ORBIT Barcode Scanner Logo

Related Topics:

Question about Metrologic Instruments MS7120 ORBIT Barcode Scanner

1 Answer

SCANER BEEPING HI. I HAVE A PROBLEM. MY SCANER MS 7120 GIVE ME LOW FREQENCY LONG BEEP LIKE EVERY 10-15 SECONDS. ITS WORKING BUT IM AFFRAID THAT SOMETHING IS WRONG. I UNPLUGED IT FROM COMPUTER AND ELECTRICITY AND PLUGED IN AGAIN BUT ITS STILL BEEPING. WHAT CAN IT BE?

Posted by KAMIL KACZMAREK on

  • thomaskvt Mar 04, 2008

    My scanner MS 7120, is beeping after every 10-15 seconds. But it scanning well. Could someone instruct me how to solve this problem.



    Please send reply to [email protected]



    Thanks

    Thomas

×

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 21 Answers

Hello,

I have a same issue with my MS-7120, how ever mine is in worse stage, when i power up, it beeps and u can see green/red light blinks on top, and it tries to spin the inner motor + tries to turn inner light on, but after several seconds it goes dead. how ever red/green light blinks on top.

i contact the company which i purchased from, he told me these scanner has life expectation of approx 3 years, after 3 yrs they die.

i was told cause is from heavy/light voltage transfer from outlet.

and they have to be repaired by orbit support.

i am afraid to tell your, sounds like urs is ready to die. just beware !!
i hope this information helps you.

Posted on Dec 22, 2007

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Bose p1 turns on but only first touch works then freezes

If you've done the complete walk around i/e--unplug from wall/remove batteries takes bout 1/2-to-1 hour don't be in a hurry then go bac & reset--if no go then your room interfac M-1 needs [email protected]
1helpful
1answer

I turn on my ps3 and the green light comes on for a short time and the it beeps three times shuts off and the green light turns red and starts to flash. If I push the power button again the red light stops...

this happens when the ps3 has overheated-try removing the hard drive and replacing then give the console a hoover out.....if this doesnt work try holding the power button on for 5 sec....if this doesnt work its back to sony im affraid
0helpful
2answers

When I turn the laptop on, I get a set of 4 beeps, repeated 4 times.

Hi,

Not good news i'm affraid, Four cycles of four short beeps and a blank screen = System board (Security chip) failure.

I'd call 800-IBM-SERV and see if they can advise. It might require a trip to the depot or they could give you instructions over the phone.


Regards.
3helpful
3answers

It does not start, gives one long beep (about 2-3 seconds) silence and beep again

Switching DDR cards solved the problem. I was getting long beeps every 2 seconds. No short beeps. Just one long beep every 2 seconds. Thanks Josh Whitehead.
1helpful
1answer

Acer aspire 7100 continually beeps while starting up

I had the same problem, I went to the keyboard and shut down the beep there is a check mark next to it and take the check mark off, the beep will stop
0helpful
1answer

LAPTOP HP PAVILION DV2000 problem

Hello!

That beeps indicated that there is a problem in the video Graphics adapter and in the memory.

try remove and clean the memory and then fix it back, im sure that would resolve your problems. however if this not solve then your should replace the memory.

If affraid to do so, then maybe let the repairman do it for you.

fixya!

best regards, melnavz
0helpful
1answer

3 beeps at start

hmmm...that's not good. works fine with no battery. I suspect your motherboard may be taking a vacation from working soon.

got backup for your HP?
27helpful
5answers

Reset wep 200

This is what I did. With deviced OFF. Do the following while in your EAR.
Press and Hold the button like if you are going to turn it on. You will hear a "Beep"...Keep pressing (do not depress when you hear the '"beep")...after for about 5 more seconds or 7 you will hear a second "beep". Look at your Headset....and I noticed the light was a solid blue. I got curious and told my phone to look for devices...and in a matter of 2 seconds..Bam I saw the name...Even though it didn't read as Wep200. It says "Samsung H200", but I don't have anything samsung at home, so i picked that name and it works.

Note: I did all that in the bathroom, out of any interference. Maybe im superstitious.
Hope it helps.
Not finding what you are looking for?

923 views

Ask a Question

Usually answered in minutes!

Top Metrologic Instruments Computers & Internet Experts

Marvin
Marvin

Level 3 Expert

85242 Answers

Brad Brown

Level 3 Expert

19166 Answers

Cindy Wells

Level 3 Expert

6648 Answers

Are you a Metrologic Instruments Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...