Question about D-Link AirPro DI-764 Wireless Router

1 Answer

DWL 2100AP problem

I have D-Link 2100AP restarts automatically, (Power led flashes for some time but by the time it connects to lan port it restarts automatacally as soon as lan led lite up.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

If you can get into the built in webpage to upgrade firmware I would suggest upgrading it. Sounds to me like corrupted firmware. If you can I would return the device. I had a similar issue with a linksys AP and I found out that the Firmware was scrubbed. Had to send it back to the manufacture.

Posted on Jun 18, 2007

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to know how I can re-set my 3Com 3crwe955275 wireless access point to its default factory settings. Can anyone help?


1 Remove power from the Gateway. 2 Disconnect all your computers and the cable/DSL modem from the Gateway router. 3 Using a straight through Ethernet cable, connect the Ethernet Cable/DSL port on the rear of the Gateway to any one of the LAN ports. 4 Re-apply power to the Gateway. The Alert LED will flash as the Gateway starts up, and after approximately 30 seconds will start to flash more slowly (typically 2 seconds on, 2 seconds off). Once the Alert LED has started to flash slowly, remove power from the Gateway. 5 Remove the cable connecting the Cable/DSL port to the LAN port, and reconnect one of your computers to one of the Gateway LAN ports. 6 Re-apply power to the Gateway, and when the start-up sequence has completed, browse to: http://192.168.1.1 and run the configuration wizard. You may need to restart your computer before you attempt this. 7 When the configuration wizard has completed, you may reconnect your network as it was before

Here on page 85 of the manual
3Com 3CRWE53172 User Manual Forgotten Password And Reset To Factory...

Feb 18, 2015 | 3Com Computers & Internet

1 Answer

Admin


If the default password on the D-Link has been changed then
To reset the DLink back to the default settings -
Press and hold the RESET button at the back of the router with the power ON until the LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, open the browser on your laptop/computer and enter the D-Link's configuration URL
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter)

Apr 30, 2013 | D-Link DI 514 Wireless Router (DI-514)

1 Answer

The led of power supply turned on and turned off three time and stop


Have you tried unplugging and plugging the power supply back in? If that doesn't help, try to check the manual for power issues:
Link DWL 2100AP user manual

Oct 19, 2012 | D-Link AirPlus Xtreme G DWL-2100AP...

1 Answer

The power led is hardly working and the router is not responding


Try reseting the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings. To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Apr 26, 2011 | Linksys Wireless-N WRT150N Router

1 Answer

I just got aWBR2310 router with no hook up instructions how do i hook it up to my modem


If the default password has been changed then -
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter)
You can now configure the wireless settings. To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security
After configuring the wireless card in your laptop/computer with the D-Link's wireless settings then,
remove the LAN cable from the computer and D-Link then connect the LAN cable to your DSL or cable modem then connect the other end of the LAN cable to the D-Link's WAN or Internet port.
You can now surf the Internet using the D-Link wireless connection.

Apr 14, 2011 | Computers & Internet

1 Answer

Cannot set up network


If the default password has been changed then -
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your computer's LAN port, open a browserand enter the D-Link's configuration URL. OR open the browser on your laptopand enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter)
You can now configure the wireless settings. To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Mar 29, 2011 | D-Link AirPlus Xtreme G DWL-2100AP...

3 Answers

I have a dwl-2000ap, the problem on the lan port does not function, led indicator lan does not work. I have input cable type Straight-Through or crossover, but it still does not function whether dwl-2000ap...


It should work with either cable. The LED will only come on when a connection is made to the computer or router. Is the LAN adaptor working correctly at the other end.

Jul 19, 2009 | D-Link AirPlus Xtreme G DWL-2100AP...

1 Answer

Airplus xtreme g doesn't work


I have have this happen before with D-Link routers. Check your ac adaptor for power. If there is power to the adaptor, then the power supply in the router is gone and needs to be replaced.

Mine blew up unexpectedly and I replaced it with a linksys.

Jun 09, 2008 | D-Link AirPlus Xtreme G DWL-2100AP...

1 Answer

Power on and off


it is not the power, but it is searching for a signal to connect to via cable. make sure the cable is connected correctly

Jan 06, 2008 | D-Link AirPlus Xtreme G DWL-2100AP...

Not finding what you are looking for?
D-Link AirPro DI-764 Wireless Router Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4367 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...