Question about Sharp AL-1661CS All-In-One Laser Printer

1 Answer

Machine having problems Locating TD cartridge

When machine shuts off and turns back on it has a problem locating the TD cartiridge unless tilted forward

Posted by Jay Brown on

Ad

1 Answer

Anonymous

Replace the toner cartridge.

Posted on Jun 15, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do i find the drain plug on whirlpool duet washer


You have to be more specific. Is the machine not draining? It drains under the drum which has a tendency to clog over time from lint etc. There is a catch screen but that can become clogged also. You can tilt the machine forward to access the bottom. On the right side you'll see the black drain hose. If there is water in the machine, be careful tilting it forward as the water may run out. If you want to access the drain from inside, you have to remove the drum. As the drum has a tendency to stick to the shaft, you halve to use a piece of 2"X4" and a scissor jack or bottle neck hack on the shaft to lift it off of the shaft. To access the drum you first need to tilt the top back off first. They is two spring clips located approx. 6 inch in on either side under the top piece. Use a narrow putty knife to locate them and push them in and up. The back of the top is hinged so be careful tilted it back. when you push on the clip lift up on the top part of the machine at the same time. Good luck.

Dec 13, 2016 | Whirlpool Washing Machines

1 Answer

Washer is out of balance in the dpin cycle since we installed a new floating floor in our laundry room. Have tried rubber feet for levelers and sticky pads to floor, nothing seems to help.


So, is the machine level and STABLE? The final step is to tilt the machine forward on to the two front feet. This allows the rear, SELF LEVELING legs to reset. Then set the machine back on all four feet.

Sometimes the real feet get jambed and will not release unless you pry them loose. In extreme cases the rear feet damage the plastic holder that they are in...

BUT, the tilt foreward and set back on rear legs works most every time.

May 01, 2011 | Washing Machines

3 Answers

Location of battery where is it


under the hood or in the trunk

Feb 12, 2011 | 2001 Buick LeSabre

3 Answers

Kenmore elite top loader how do I get the case off?


Hi, Get me a model # and I can assist you with fixing this issue.

Vic

Jun 28, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

My washer was tilted forward and now it is making a strange noise


the wash arm may be out of alignment now you might see if something fell into the bottom of the machine.

Jan 08, 2009 | Washing Machines

1 Answer

Cold water continuously drips


fill valve bad foreign matter (sand ,rust )has gotten through filter screen and settled in fill valve not allowing it to shut off completely..(hope i get this right) to acess remove screws on rear of console and lift console forward and up valve mounts underneath console may need to lift top up to acess lower fill hose connection ..remove plug on front corners of top remove phillips screw underneath top lifts up and tilts back

Jun 28, 2008 | Fisher and Paykel IWL12 Top Load Washer

1 Answer

Switch


yes facing the washer locates the two screws. They will either be in the front or rear of the control panel or back them out far as you can. Once you have done that pull the control panel slightly forward, and tilt it back on the hinges. Now unplug the lid switch wire but don't forget to plug it back when you’re done. Next locate at the rear of the washer body the two gold clips then push forward, and take careful note of how they fit. Then pop them out with a screw driver tilt the washer body forward at 45 degree angel and walk forward with the body, and set it down. then you can acess the lid switch

Jun 17, 2008 | Kenmore 20172 Top Load Washer

1 Answer

My Whirlpool washers nuetral drain does not work, it sratrs to spin with a full load of water


you need to clear it or replace it First unplug the washer and turn off the water. If you have a shop vac take the drain hose out of the drain, and through the drain hose vacuum the water out of your washer. If you don't have a shop vac go to the auto parts store and buy a pair of radiator hose clamps. Then facing the washer locates the two screws. They will either be in the front or rear of the control panel or back them out far as you can. Once you have done that pull the control panel slightly forward, and tilt it back on the hinges. Now unplug the lid switch wire but don't forget to plug it back when you’re done. Next locate at the rear of the washer body the two gold clips then push forward, and take careful note of how they fit. Then pop them out with a screw driver tilt the washer body forward at 45 degree angel and walk forward with the body, and set it down. Now you will see the white pump and motor assembly. You should see two clips holding the pump to the motor pop them off, and pull the pump off the motor shaft.

Jun 03, 2008 | Whirlpool Washing Machines

1 Answer

Water leaking from whirlpool washer


facing the washer locate the two screws. They will either be in the front or rear of the control panel and back them out far as you can. Once you have done that pull the control panel slightly forward, and tilt it back on the hinges. Now unplug the lid switch wire but don't forget to plug it back when your done. Next locate at the rear of the washer body the two gold clips then push forward, and take careful note of how they fit. Then pop them out with a screw driver tilt the washer body forward at 45 degree angel and walk forward with the body, and set it down.

Jan 12, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Monitor is tilted forward and wont tip back


it will tilt back, just make sure the stand is in the forward most position and not turned and hold the screen at top and push while at the same time pull at the bottom, it will be quite stiff.

Sep 23, 2007 | Compaq fs740 17" CRT Monitor

Not finding what you are looking for?
Sharp AL-1661CS All-In-One Laser Printer Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

k24674

Level 3 Expert

8091 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...