Quasar VHQ400 VHS VCR Logo

Related Topics:

Question about Quasar VHQ400 VHS VCR

1 Answer

Clock The clock is blank and i cannot for the life of me figure out how to set it.

Posted by tom lancy on

  • Anonymous Feb 14, 2009

    how do i set the clock?

×

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 883 Answers

Most of these use the remote control to set clocks. Find the menu button and scroll through all options...it should be there.

Posted on Jun 10, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

My new Kenmore Electric Range, model 790.9419, purchased July 18, 2014...The clock no longer works. I press "clock", the code CLO appears; I set correct time; press START and the display goes blank an

That's an enegy saving "feature" - the ability to turn off the clock. Usually (in most models), you can turn the clock display back on by pressing and holding the clock 10 to 15 seconds.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

0helpful
1answer

I am using my mother's Elgin 3400E travel alarm

On my Elgin alarm clock, you just push the nap button and it will add 15 minute increments for a nap. I haven't figured out how to turn it off if I change my mind or wake up earlier than I set it.
4helpful
1answer

I need a manual for a Vextra CD/Clock Radio VX715. I can not figure out how to set the clock radio alarm

The settings on this clock were difficult to figure out even with the manual. I made a lot of notes in the manual to help myself each time I had to reset the clock and CD Alarm. See Attached .pdf.
2helpful
1answer

AI can't figure out how to set the atomic clock

This clock will set it's self in a 24 hour time frame. You need only set the time zone your in.

If it does not correct it;s self change walls and location in your house.

The transmitter is located in Fort Collins, Colorado. this station transmits the time codes and is best received at night.

Hope this tip helps.

R/
David
1helpful
1answer

Sony NWZ-E438F clock display is blank..

To set date and clock:

1. Go to Settings (looks like a suitcase-bag)
2. Go to Common Settings
3. Go to Set Date-Time (this allows you to set the date and time)

If you want to change date and time display format, you can also do this under common settings.

I hope this helped
22helpful
3answers

I have a chefmate digital kitchen scale and I do not know how to reset the clock.

I have the same problem. The only way I can figure out how to reset the clock is to take out the batteries and put them back in at 11:59 pm or midnight. Replacing batteries reset the clock to 12:00 am. So if you do it at midnight, you'll end up with the right time. But for the life of me, I cannot figure out how to actually set the clock using the availble buttons.
2helpful
5answers

Skyscan Atomic Clock WWVB

figure out where yu are north south west east zones on your map from where yu are , then pull battery again it should stop at for eight or twelve push time zone then set in a window facing your zone it should automatically pick it up shortly in awhile
sw i think it may stop at four also but then wait
0helpful
1answer

Cannot Figure Out Curtis Digital Frame

Okay that I found easy to do!!! I will tell you how I did it! :)
Go to setup, scroll down to clock set, right arrow and change it (by using the up, down, right,left) arrows..

What I am having problems with is how to have the pictures run without being hooked up to the camera?
I copied them to the "c" drive on the frame?
3helpful
1answer

DEH-P750MP Setting Time Pioneer

hey... i hope this it worth a 100% vote lol.. Premier CD PlayersHow do I set the clock on my single CD player? For most Pioneer single CD players, you can set the clock using the following steps: Press and hold the SOURCE button until the unit shuts off. Press and hold SOURCE again until the clock appears. With some models you will press and hold the FUNCTION or AUDIO button instead of the SOURCE button. Press the left or right arrow to select the segment of time you wish to adjust. Press the up or down arrows to increase or decrease the numbers in the blinking segment. Once the clock is set correctly, press the SOURCE button to exit.
1helpful
1answer

Set Clock

Here's the link to the manual; http://books.jvcservice.com/download/686537201/34916.pdf page 9 should help you out :)
Not finding what you are looking for?

Open Questions:

See all Quasar VHQ400 VHS VCR Questions

82 views

Ask a Question

Usually answered in minutes!

Top Quasar Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76835 Answers

 Grubhead
Grubhead

Level 3 Expert

5720 Answers

Brad Brown

Level 3 Expert

19008 Answers

Are you a Quasar Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...