Remote codes panasonic tv for onyko rc-693m

RC: Living Solutions (or Innovage) jumbo universal ...

Remote Central https://www.remotecentral.com > rc-remote > thread
Jun 10, 2007 - Hold the device button you want to program for 3 seconds & release. Push & release the power button & the red light will remain lit. Push the ...

Living Solutions Jumbo remote need codes - RC
5 posts
Jan 18, 2008
RC: Living Solutions Jumbo URC - Remote Central
6 posts
Jun 20, 2011
More results from www.remotecentral.com

Remote Codes / Universal Remote

Vizio https://support.vizio.com > article > Remote-Codes-Un...
Remote Codes / Universal Remote ; 2 Digit TV Remote Codes 19 ; 3 Digit TV Remote Codes 502 627 004 113 505 011 ; 4 Digit TV Remote Codes 1758 0178 1756 0128 0117

Missing: Living ‎ solution

How to Program a Living Solutions Universal Remote

Techwalla https://www.techwalla.com > Tech Support > How To
Point the remote at the device you are programming and press the corresponding device button on the remote. These buttons are labeled "TV," "VCR", "DVD," etc.

To program a universal remote control for your Panasonic AV Control Receiver SA-HT05, you will need to know the remote control code. There are a few ways to find this code.
First, you can check the manual that came with your universal remote control. Look for a list of codes for different devices, including the Panasonic AV Control Receiver SA-HT05. Find the code that corresponds to your receiver model.
If you can't find the code in the manual, you can search online for a list of remote control codes for the Panasonic AV Control Receiver SA-HT05. There are many websites that offer this information for different models of devices.
If neither of these options works, you can try entering different codes from the list provided by your universal remote control manufacturer. Follow the instructions provided in the manual for how to enter the code, and try different codes until you find one that works.
It's important to note that not all universal remote controls are compatible with all devices. If you're unable to find a code that works with your Panasonic AV Control Receiver SA-HT05, you may need to purchase a remote control that is specifically designed for that receiver model.

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. The site has set-up code list & set-up procedure to many popular brand remote controls. The site has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Set-up code list to many brand remote controls also is given. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://electro-medical.blogspot.com/

Anne try these codes if not use the links below.
3# codes 012, 013, 038, 086
4# codes 1003, 1054, 1055, 1062, 1109, 1130, 1170, 1246, 1253, 1275, 1277, 1286, 1289, 1350, 1389, 1392, 1406, 1418, 1419
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
RCA universal remote control codes for RCR450 RCR815 RCR412 and other...

RCA Remote Code Finder

RC Programming Your RCA Remote Control



How To Program an RCA Universal Remote Control

0291,0265,02910. Try these codes. For more information http://electrohelponline.blogspot.com/ Setup procedure, and setup code list to many popular remote controls are given. Pull up older posts.

Manual says: 1. While holding down the REMOTE MODE button for the mode in which you want to use the command, press the [ON] button. *** Hold both buttons down for 3-4 seconds *** 2. Press the button you want to learn the new command 3. Point the remote controllers at each other, about 2-6 inches apart, and then press and hold the button whose command you want to learn until the Remote indicator flashes. *** Hold them level with each other, 2-3 inches apart, and don't move them at ALL while you press the button on the old remote *** 4. To learn more commands, repeat steps 2 and 3. Press any REMOTE MODE button when you've finished. *** If the command was learned correctly, the remote indicator will flash *SLOWLY* twice - about a 1 second blink, and the red light will remain on. If the command was NOT learned correctly, it will blink twice *QUICKLY* - about .5 seconds, and the red light will go off. *** If the red light stays on, you're golden - keep going until you get to a button that flashes red quick and the light goes off. Some of the buttons I programmed took 6-7 tries in exactly the same position to learn.

Look under the TV's Model number on the Onkyo website. The only remote control info you'll find for your factory TV remote control is listed in the service manual of the TV Reciever you own.

There is an easy way to setup this remote controllerl(RC). It called "Automatic Code Searching" which means that you don't have to even find the code. The controller will searching it for you. Just do the following steppes.

1. Turn on the "Device" to be remotely controlled, e.g. TV, VCR.

2. Point the RC right to the "Device" .

3. Press a device button on the RC represent the "Device", e.g. TV, VCR, DVD etc. You can see the indicator lid flash once.

4. Press the SET and than the POWER button on the RC. hold both buttons for 2 seconds or more, you will see the red lid on. then release both buttons simutenously. after that the indicator lid will be flashing, means the searching started.

5. Keep pointing the RC to the "Device" until it is shut down by the RC, Press any button in 1.5 second to finish the setting.

You can try the RC now. It should work. My one is working.

You need to program the VCR (which turns the sey on/off) as an aux, then program any Panasonic TV type for TV, and then set the STB button to control STB, TV and AUX and you should be set.