Question about Marantz SR7005 Receiver

Open Question

Sr7005 stuck in firmware update

My SR7005 marantz receiver is stuck in an update firmware loop.. How do I reset the chip or get it to update firmware?

Posted by Anonymous on

Ad

1 Related Answer

Anonymous

  • 8546 Answers

SOURCE: Hi There, I have a

It sounds like you've read one of my many posts on 901 deployment in the AV world.

Functionally, what is the difference between one amp with 'x' channels or 'x' mono amps? Nothing. Pre-outs don't know or care what else an external amp does.

According to this link http://www.ecoustics.com/electronics/products/new/642968.html those amps are 2- and 5-channel, respectively.

There was a time when I had two bridged-mono Carver Cube atmps (at a real 400 watts) pushing one 901 each but that was big time overkill.

I now use a Carver AV-406 (functionally the same as your MM7055) with the 901 EQ in between the AV Receiver's front pre-outs and two 110-watt channels. Other channels on the AV-406 pull subwoofer and surround back duties. My AVR directly powers only the center and surround speakers.

The MM7025 would work for you.

Posted on Jul 07, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

All of a sudden stopped working and won't turn back on. been 12hrs. when power is pressed, it turns on for 2 seconds and then standby lights blink again and it turns off

This could be caused by a direct short circuit on the speaker outputs. Try disconnecting all the speaker connections at the back of the receiver and then power back on. You can also try a factory reset by holding the surround mode + clear button for 3 seconds.
0helpful
1answer

Marantz SR7005 not working.

I have the same receiver SR7005 and the HDMI board went out. The boards are on back order and weren't expected to ship for a month or so. Magnolia, the store where I purchased it gave me a new receiver. I think they might be having issues with this board. The board went out on 4/30/12, just got my new receiver 6/21/12. I have a feeling that this will happen again and others will have the same issue. All you need is a new HDMI board, the processor went out in it.
0helpful
1answer

Maranz sr7005 no sound

Most of the time no sound means fuses have blown or output transistors
0helpful
1answer

Upgrade id disappeared

Hello
All these details are in its repair book. There are so many adjustments should be done, and all are described in detail in that book. I've the book, but aI can't send it to you by this window as it does not allow ma to upload PDF files by it. If you come over me by purchasing any one among the audio services advertised at Fixya, I'll send you both the user manual and repair book to you by return mail. The repair book is very usefull to you as it contains all the internal circuit details, schematics, possible repair and its remedies. OK.
0helpful
1answer

Hi There, I have a Marantz SR7005 Receiver and Bose 901 Series VI speakers with the Bose equalizer. I'm struggling to figure out the best way to connect the Bose equalizer/speakers to the SR7005. ...

It sounds like you've read one of my many posts on 901 deployment in the AV world.

Functionally, what is the difference between one amp with 'x' channels or 'x' mono amps? Nothing. Pre-outs don't know or care what else an external amp does.

According to this link http://www.ecoustics.com/electronics/products/new/642968.html those amps are 2- and 5-channel, respectively.

There was a time when I had two bridged-mono Carver Cube atmps (at a real 400 watts) pushing one 901 each but that was big time overkill.

I now use a Carver AV-406 (functionally the same as your MM7055) with the 901 EQ in between the AV Receiver's front pre-outs and two 110-watt channels. Other channels on the AV-406 pull subwoofer and surround back duties. My AVR directly powers only the center and surround speakers.

The MM7025 would work for you.
0helpful
1answer
0helpful
1answer

Hi, I have recently purchased an SR7005 which is connected to an HD PVR via Audioquest Cinammon HDMI cable. While watching programs, I lose audio immediately after an advertisement break. If I pause...

If you are watching adverts that implies a broadcast TV sound signal. What happens is that the broadcaster will switch off sound especially Dolby signals during add breaks. Therefore it could be your TV that stops sending the sound to the Marantz. So check the sound settings of you TV. It might have an auto feature that detects the signals, that could be switched to manual or just a wrong sound signal that causes the problem.
0helpful
1answer

My sr 7005 loses a signal for 2 seconds when watching a bluray or cable

It takes two, maybe more to tango - plus the cables that carry the various signals.

Can you define the signal loss better? Where do you detect it?

Audio, video, both?
Optical, HDMI, component ????

Try a different input or output port on the Marantz to isolate the source(s) as contributors.
0helpful
1answer

Need PDF User Guide

Hello
Send your email address to me by Fixya comment. I've the user manual to your device in PDF format. I'll send a copy of it to you by return mail. OK.
0helpful
1answer

It's impossible to stop the firmware update process. We' ve tried both:press and hold the ON/STANDBY on the main unit for more than 5seconds and remove and re-insert the power cord, as advised in the user...

Hello
You must have its repair book, not the user manual, with you to know all about the firmware update and other things. There are so many adjustments should be done after firmware update, and all of them cannot be snd to you by this window, ad they contains illustrations.
If you are interested to get a copy of the repair book, you have to muy one amomg my audio services advertised at Fixya. Send your email address by that window, so that I can upload both the user manual and repair book to you by return mail. Both of the together will come over 35MB. OK.
Not finding what you are looking for?

Open Questions:

See all Marantz SR7005 Receiver Questions

Marantz SR7005 Receiver Logo

Related Topics:

303 views

Ask a Question

Usually answered in minutes!

Top Marantz Audio Players & Recorders Experts

The Knight
The Knight

Level 3 Expert

76785 Answers

 Grubhead
Grubhead

Level 3 Expert

5720 Answers

Brad Brown

Level 3 Expert

18821 Answers

Are you a Marantz Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...