Question about Dewalt DW411 quarter - sheet palm grip sander with dust collection

1 Answer

Can the platen on DW411 be replaced - Dewalt DW411 quarter - sheet palm grip sander with dust collection

Posted by Jeffrey Wansak on


1 Answer

Repair Ahjoshe

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Dewalt Master
  • 885 Answers

Yes it can be replaced. If you go to, you can look up your sander and find the parts you need. You can buy the parts there or get the part numbers and search the web for pricing.

Posted on Dec 04, 2012


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Palm sander

The answer "Go to Dewaltservicenet" can be confusing - the actual site is and even then, entering your part to get to manual can be infuriating. This is the link for the current model which, for all intents and purposes, is the same. The link to the helpful page is: . You'll get a pop-up box with a dropdown that has a few numbers, nothing else. Just click on "1" and ignore language that indicates that this model has more than one - it does not. After you click on "1", the pop-up disappears that you're on the d/l page. Downloads are in the upper right corner. You want "Instruction Manual".You should get to this page: but may not, it's very glitchy. On this page, you'll want to make sure "Sanders" is on the left and "sheet" is on the right. If you try to get the Manual from the DW411 page, a blank page will open. Make sure your pop-up blocker is off or that you allow The instructions for the d26441k are identical to the dw411 - same technique for loading sanding sheets, same rods, etc. I've uploaded the d26441k page manual .pdf so that should help. It's easy to get lost on the Dewalt site while trying to find somthing so simple. :)



May 24, 2014 | Dewalt DW411 quarter - sheet palm grip...

1 Answer

The platen won't stay in place so only the top half of the characters are showing

If the right platen latch is broken it can easily be replaced to lock down the platen. If the left one is damaged then you have to replace the entire platen as that is much more difficult to repair.

Apr 04, 2014 | IBM Personal Wheelwriter 2

1 Answer

I cannot print from canon ip2770 printer...the orange light flashes five times

  1. Download software for Canon iP1200, iP1600, 2200 Printers.DOWNLOAD Service Tool Software for Canon Pixma Printer iP1200, iP1600, iP2200
  2. Unzip downloaded file by WinZip, 7Zip, Izarc, etc
  3. Run GeneralTool.exe
  4. Select the connected USB port number from USB PORT
  5. Click LOCK RELEASE, and select the applicable model name in SET DESTINATION
  6. In CLEAR WASTE INK COUNTER, select MAIN or PLATEN. The selected waste ink counter will be reset. MAIN resets the main waste ink counter, PLATEN resets the platen waste ink counter.
If both the main and platen waste ink absorbers are replaced, reset both the main and platen waste ink counters.

Jul 06, 2011 | Office Equipment & Supplies

1 Answer


if your platen calibration is not done.
1 Resat All Platen Connection of cabal
2 Replace Logic Card
3 Check Platen Moving proper
4 Than Check Sensor And Platen Aliment
5 Than replace Platen Sensor
6 Please Check Platen Motor
yogendra Sharma

Nov 27, 2010 | Tally 6312 Matrix Printer

1 Answer

Air and dust no longer blow into dust collection bag. I suspect that there is a clog somewhere.

are you putting holes in the papper with the guide? there has to be holes in the paper for the dust collection to work

Oct 15, 2010 | Dewalt DW411 quarter - sheet palm grip...

1 Answer

Where can I get instsructions for the Dewalt DW411 Palm grip sander and also what type of sand paper do I get to fit it.

go to and in the midle of the page and towards the bottom under need manual type in your model number and you should be able to download anbreakdown and operators manual

Oct 05, 2010 | Dewalt DW411 quarter - sheet palm grip...

1 Answer

Need to find replacement switch part

best way is go to and they have a service/repair center locator section type in your information and you can find one pretty close that way. Also you can download a schematic for the tool while you are there.

Sep 23, 2010 | Dewalt DW411 quarter - sheet palm grip...

2 Answers

Procedure for replacing platen on QS-900

I dont think that you are missing anything, but you might want to go to and download a breakdown for this tool. it might be that the platen is stuck and needs some "gentle" persuassion to remove.

Jul 12, 2010 | Black & Decker QS800 2.0 Amp 1/4 Sheet...

1 Answer

Z4Mplus has a worn/cut platen roller

did you try to find info at manufacrturers website or email them?

Jul 06, 2009 | Zebra Z4M Printer

1 Answer

Replace S4M Platen Roller

Call Brian at Peak Technologies for the platen roller 877-863-2522 xt. 6807

Jan 09, 2008 | Zebra S4M Thermal Label Printer

Not finding what you are looking for?
Dewalt DW411 quarter - sheet palm grip sander with dust collection Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Tools & Hardware - Others Experts


Level 3 Expert

1997 Answers

john h

Level 3 Expert

23515 Answers

Tim Venetis

Level 2 Expert

260 Answers

Are you a Dewalt Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides