How do i program a hrmc-11 remote - Hughes HRMC11 Remote Control

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the site linked here. It has set-up code list & set-up procedure to many popular brand remote controls. See it in "Mosaic" or "Magazine" view. It will make surf easier.
http://electrohelponline.blogspot.com/
http://remotesearch.blogspot.com/

Hello
Codes for RCA tv with Hughes remote are:

160 161 156 165 065 070 004 023 024
056 074 081 152 167 145
Code Entry

Use the REMOTE pane under the System Setup menu tab to program your

HRMC-11, HRMC-12, or HRMC-13 remote control to operate your TV, VCR,

SAT, AUX device, or DVD (HRMC-11 and HRMC-12 only). The AUX menu

button can be used to control a CATV box or other type of device. Use the menu

buttons to choose the desired type of device and display a brand name menu list
from which you can select the manufacturer of your device.

Code scanning

To use the Code Scanning method:

1. Repeatedly tap the top part of the CHANNEL (CH) button.

2. Continue to step through the codes until the component turns off, indicating

you have found the correct component code. If you accidentally pass a code

that responds or realize you may not have been aiming the remote control at

the component, tap the lower part of the CHANNEL (CH) button to step

backward through the codes.

3. Press the remote control POWER button to verify the proper code by

turning the device on and off.
4. Press the device button (in this example, TV) again to lock in the code.
OK

from the book: this is for the HRMC-5 may be the same.
Code Scan if you don't know the code.

Keep remote aimed at the device you want to control. during the programing, the device will send out a "power" command for the device being programmed.

While holding down the device key(i.e., TV) that you are programming, press the "Mute key for one full second. then release the keys. the device key should light up and stay lit. if not, repeat the process.

repeatidly tap the channel up key to step through the codes, sending out the "power command". may take some time, many codes. when device shuts off, you have found the code. If you inadvertantly went past the code, that responded, you can press the channel down key to go back. press the "power key to verify you havent missed the code. In order to lock in the code, press the device key again. the remote will remember the code till you re program it.

Yes, follow the links:

http://www.remotegarage.com/cable-t-v-remotes/hughes-hrmc-11-directtv-remote-control.html

or

http://www.remotecontrolwarehouse.com/HUGHES/HRMC11.html

hope this solution is helpful. Please rate this solution.

dont have codes for programing HRMC-5 (11), I HAVE A SYMPHONIC tv

I have a HRMC-8 remote. Cant find the manual and need to program for a different TV?

Hold down Select and Mute until the tv light flashes. The enter the code and press Select.

http://www.directv.com/learn/pdf/System_Manuals/Hughes/HNS_SD_HBH.pdf
remote programming instrutions start on page 49 of the PDF file and give step by step instructions for programming your remote

I HAVE A TOSHIBA TV AND I WANT TO PROGRAM MY REMOTE TO WORK BOTH. THE REMOTE IS A HRMC-B

HRMC 15 Code Scanning method...
1.Press TV device button on the HMRC 15
2. Press Select and Mute simultaneously until TV device button flashes.
3. TV device Button should now stay lit.
4. Aim Remote at TV
5. Press The CHANNEL button UP ...repeat until your TV turns off.
6. Press Power Button to turn TV back on (Thus confirming you found the right code).
7. Press the TV device button to lock in code.
8. ENJOY !!!